Hoshizaki IM-21CLE Manual De Instrucciones página 5

ENGLISH
1. OPERATION
The installer will normally commission the icemaker to start the
automatic icemaking process. To ensure continuous operation, make
sure that:
* The water supply tap is on, and
* The icemaker is plugged into the power supply.
2. PREPARING THE ICEMAKER FOR LONG STORAGE
) Unplug the icemaker or disconnect the power supply.
2) Close the water supply tap, and remove the Inlet Hose.
3) Remove all ice from the Storage Bin, and clean the Bin.
4) Ask for draining of the icemaker by professional qualified personnel.
III. MAINTENANCE
1. CLEANING
WARNING
. Before carrying out any cleaning or maintenance operations,
unplug the icemaker from the electrical supply network.
2. Ask a trained service person to clean and sanitize the
icemaker water system at least twice a year and to check
and clean the Condenser at least once a year.
3. This appliance must not be cleaned by use of a water jet.
[1] Exterior
Wipe the exterior at least once per week with a clean, soft cloth. Use
a damp cloth containing a neutral cleaner to wipe off grease or dirt.
[2] Scoop and Storage Bin Handle Cleaning/Sanitisation (Daily)
) Either mix 3 litres of water with  ml of 5.25% sodium hypochlorite
solution in a suitable container, or the recommended Hoshizaki
sanitiser as directed.
2) Soak the Scoop in the solution for more than 3 minutes. Rinse
thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
3) Use a neutral cleaner to wash the Storage Bin Handle. Rinse
thoroughly.
4) Soak a clean cloth with the sanitising solution, and wipe the Handle.
Use fresh water and a clean cloth to rinse/dry.
[3] Storage Bin Interior Cleaning/Sanitisation (Weekly)
) Open the Storage Bin Door, and remove all ice.
2) Wash the Bin liner with a neutral non-abrasive cleaner. Rinse
thoroughly.
3) Soak a clean cloth with the neutral cleaner, and wipe both sides of
the Slope and the Door inner surface. Wipe off the cleaner with a
clean damp cloth.
4) Either mix 3 litres of water with  ml of 5.25% sodium hypochlorite
solution in a suitable container or the recommended Hoshizaki
sanitiser as directed.
5) Soak a clean sponge or cloth with the solution, and wipe the Bin
liner, Bin Door and Slope.
6) Rinse thoroughly with fresh water and a clean cloth to wipe off the
solution. Close the Bin Door.
Note: Some solutions may cause damage to the Bin liner surfaces
or corrosion on the metal parts. Always rinse the sanitiser
unless directed otherwise by Hoshizaki guidelines.
[4] Air Filter (Air-Cooled Model Only)
A plastic mesh Air Filter removes dirt or dust from the air, and keeps
the Condenser from getting clogged. As the Filter gets clogged, the
icemaker's performance will be reduced.
[IM-45LE/65]
Remove and clean the Air Filter at least twice per month:
) Remove the Front Panel (Lower).
Note: Do not put your hand inside the machine compartment.
2) Remove the Air Filter.
3) Clean the Air Filter by using a vacuum cleaner. When severely
clogged, use warm water and a neutral cleaner to wash the Air
Filter.
4) Rinse and dry the Air Filter thoroughly, and place it in position.
[IM-2/25/30/45CLE/00/30/240]
Contact an authorised Hoshizaki service company to complete Air
Filter cleaning as part of a regular maintenance programme.
[5] Icemaking Water System
To keep the icemaker hygienic, periodic cleaning of the icemaking
water system is recommended. Always ask a trained service person
to clean the water system.
Note: . The Washing Switch on the side of the Control Box is
intended for use by service personnel only.
2. During normal icemaking operation, keep the Washing
Switch in the "ICE" position.
[IM-2/25/30CLE]
Power Cord
[IM-240M2E/WM2E]
Washing Switch
[Except IM-2/25/30CLE, 240M2E/WM2E]
4
Control Box
Washing Switch
* Control Box is located at
the rear of the unit.
(Front)
Control Box
Washing Switch
Control Box
Fig. 9