GRAPHITE 59G892 Manual De Instrucciones página 7

• Damaged safety components must be replaced immediately.
• Never overload the saw by causing the blade speed to slow down
considerably.
• Keep the work area clean. Waste or unnecessary items must be
tidied up before starting work.
• No members of the public should be in the area where the chainsaw
is being used.
• The workplace should be well lit.
• There must be no distractions for the person working the chainsaw.
• Once the engine has been switched off with the switch, never
attempt to stop the cutting disc by exerting lateral pressure on it.
• A damaged cutting disc must be replaced immediately.
• Never use cutting discs with characteristics other than those
specified in this manual.
• Never attempt to dismantle the saw's safety components or
disconnect them.
• If you need to stop working, complete the cutting operation in
progress and switch off the saw.
• If you need to stop and leave the work area, switch off the saw with
the switch and disconnect it from the power supply by removing the
cord plug from the power socket.
• Check the condition of the table saw before starting work
• Are all safety components operational and functioning as intended?
• Have the screws and other fasteners come loose?
• have the setting keys been removed?
• Always make sure that the workpiece is fully flush against the saw
table.
• Never cut several pieces of material at the same time.
• Do not disconnect the table saw from the power socket by pulling on
the cord. Protect the power cord from excessive heat, oil and sharp
edges.
• When operating the chainsaw, adopt a standing position to ensure
balance.
• All saw components must be properly fixed.
• Repairs to the chainsaw should only be carried out by a qualified
person at an authorised service workshop, using original spare
parts.
• Profile cutting must not be carried out with the saw.
• When handling the saw, only grasp the transport handles, do not
grasp the saw component covers.
PICTOGRAMS AND WARNINGS
Read the operating instructions, observe the warnings and safety
conditions contained therein!
CAUTION: Take special precautions! Risk of shearing
Wear ear protectors
Before carrying out any maintenance or repair work, disconnect
from the power supply
Wear ear protectors
Wear safety goggles
Wear protective gloves
Keep children away from tools
DESCRIPTION OF THE GRAPHIC ELEMENTS
The numbering below refers to the components of the device
shown on the graphic pages of this manual.
Designation
1 Cutter legs
2 Leg fixing knobs
3 Cutting length lock
4 Work top
5 Guide
6 Cutting head
7 Power cable
8 Plug with RCD protection
9 Power cable and water tube cover
Description
10 Water supply pipe
11 Bevel cutting angle adjustment lock
12 Electromagnetic switch
12a Switching on the device
12b Switching off the device
13 Feed mechanism handle
14 Shield
15 Cutting disc
16 Base with water tank
17 Cut stop bar
18 Water circulation pump
19 Angle indicator for bevel cutting
20 Angle gauge for slitting
* There may be differences between the graphic and the actual
product
CONSTRUCTION AND APPLICATION
The tile table saw is designed for wet cutting of ceramic tiles or similar
materials, of a size appropriate to the size of the saw itself. It is not
permitted to use the saw for cutting wood or metal. Only cutting discs
designed for this type of machine should be used with the saw. The
chainsaw has been designed for all DIY (do-it-yourself) work.
Do not misuse the device.
OPERATION OF THE DEVICE
NOTE: Make sure that the cutter is disconnected from the mains
supply before carrying out any adjustment work on the cutter.
ATTENTION: The mains voltage must correspond with the voltage
indicated on the rating plate of the cut-off machine. The cut-off
machine may only be switched on when the material to be cut is
away from the cutting disc.
PREPARATION FOR WORK
The tile cutter is delivered disassembled. Remove the components from
the packaging and assemble it.
• Fix the legs fig. A1 to the base fig. A16 and secure with screws
(supplied).
• Place the head with the worktop in the base making sure that the
water pump fig. C18 is fixed in the right place in the base (if
necessary, slide the water pipe over the spigot of the circulating
pump).
• Fit the cutting length stop lock knobs fig. A3.
• Mount the head holder
• Loosen the head lock screw
• Connect the adjustable protractor to the stop bar Fig. A17 using a
screw (the adjustable protractor can be mounted on both sides of
the work table).
• Ensure that all assembled components are fitted correctly and firmly
so that they do not move while working, increasing the risk to the
user during operation.
ATTENTION: Before starting the actual work, the saw must be
started after assembly to ensure that all parts are correctly fitted.
NOTE: The head lock screw must be unscrewed before using the cutter.
Otherwise it is not possible to move the head together with the cutting disc.
The water pump should be submerged in water when cutting.
ON/OFF
Switching on - press button I of the switch Fig. B12a.
Switching off - press button O of the switch Fig. B12b.
The power cable plug of the cutter is equipped with a residual current
protection device. The correct operation of the residual current protection
must be checked before starting the machine.
• Insert the plug into the power socket.
• Press the "Reset" button - the power light will turn red.
• Start the cutter.
• Press the "Test" button - the light will turn black and the cut-off
machine will switch off.
• Press the "Reset" button again and start work.
In the event of a malfunction of the residual current protection (other than
that described above), it is absolutely necessary to unplug the power cable
from the mains socket and refer the device for repair at an authorised
service centre.
CUTTING
The water pump, supply line and water hose must not be in the cutting
area. The cutting disc must reach maximum speed before starting to cut.
Wait until the cooling water jet reaches the cutting disc.
The base of the adjustable protractor acts as a longitudinal stop bar.
7