Publicidad
Idiomas disponibles
Idiomas disponibles
@ Cleaning of the internal parts should be performed only by
qualified service personnel.
@ Damage Requiring Service — The unit should be serviced by
qualified service personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen or tiquid has been spilled into the ap-
pliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits
a marked change in performance; or
E. The appliance has been dropped or the enclosure damaged.
@ Servicing — The user should not attempt to service the appliance
beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
® This apparatus complies with requirements of EEC directive
82/499/EEC.
SPECIAL CAUTIONS FOR COMPACT
DISC PLAYER
THIS PRODUCT UTILIZES A LASER. USER OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESLUT IN HAZARDOUS
RADIATION EXPOSURE.
"CLASS 1 LASER
PRODUCT"
This label on the rear panel states that:
1. This unit isa CLASS
1 LASER PRODUCT
and employs a taser
inside the cabinet.
2. To prevent the laser from being exposed, do not remove the
cover.
Refer servicing to qualified personnel.
PRECAUTIONS
1. Warranty Card
The serial number is written on the rear panel of this unit. Copy
the serial number and mode! number onto your warranty card
and keep it in a safe place.
2. Power
WARNING
BEFORE TURNING ON POWER FOR THE FIRST TIME, READ
THE FOLLOWING SECTION CAREFULLY.
@ Some models are designed for use only with the power supply
voltage of the region where they are sold.
U.K. and Australian Models:
AC 240V, 50Hz
European model:
AC 220V, 50Hz
(except U.K.)
USA & Canadian models:
Worldwide model:
AC120V, 60Hz
AC 110, 120, 220 and 240V
switchable, 50/60Hz
®@ Voltage Selector (Rear Panel)
Worldwide models are equipped with a voltage selector to
conform with local power supplies. Be sure to set this selector
to match the voltage of the power supply in your area before
turning the power switch on. Voltage is changed by
switching the voitage selector with a screwdriver or similar
instrument to the 110V, 120V, 220V and 240V position.
Confirm that the selector has been set to the correct position
before turning the power switch on.
If there is no voltage
selector switch on the unit you have purchased, it can only
be used in areas where the power supply voltage is the same
as that of the unit.
SE8a
at AC 110V
at AC 120V
at AC 220V
at AC 240V
Power Suppiy
Worldwide models: AC 110V. 120V. 220V 240V. 50Hz/60Hz
3. Do
Not Touch the Player with Wet Hands
Do not handie the player or power cord when your hands are
wet or damp. if water or any other fiquid enters the player cabinet,
take the player to an authorized service station for inspection.
4. Location of the Player
®
Place the Player in a Well-Ventilated Location.
Take special care to provide plenty of ventilation on all sides
of the player especially when it is placed in an audio rack.
If ventilation is blocked, the player may overheat and mal-
function.
®
Do not expose the player to direct sunlight or heating units
as the player's internal temperature may rise and shorten the
life of the pickup.
@ Avoid damp and dusty places and places directly affected
by vibrations from the speakers. In particular, avoid placing
the unit on or above one of the speakers.
@
Be sure the player is placed in a horizontal position. Never
place it on its side or on a slanted surface as it may mai-
function.
®
Do Not Place Near Tuners and TV Sets.
!f placed next to a TV or other tuner, it may cause reception
interference resulting in some noise in the TV or tuner output.
5. Care
From time to time you should wipe off the front and rear panels
and the cabinet with a silicon or other soft cloth. For heavier
dirt, dampen a soft cloth in a weak solution of mild detergent
and water, wring it out dry, and wipe away the dirt. Following
this, dry immediately with a clean cloth. Do not use rough
materiai, thinners, alcohol or other chemical solvents or cloths
since these may damage the finish or remove the panel lettering.
6. Points to Remember
@ If the player is brought from a cold enviroment to a warm
one or is in a cold room that is quickly heated, dew may form
on the pickup preventing proper operation. In this case, re-
move the disc and leave the power ON for about one hour
to remove the dew.
@ Always close the disc tray when not loading or unloading
discs to protect delicate internal parts from dust.
@ When transporting the player. Be careful not to bump it.
BEFORE USING THIS UNIT
Before using this unit, remove the transport screw and the
locking plate (Fig. 1). For safe keeping, insert the short end
of the locking plate back in the slot and replace the screw
to hold the plate in place. (Fig. 2)
-3-
Publicidad
