Publicidad
Idiomas disponibles
Idiomas disponibles
User Manual
Assemble Introduction
1
2
Attaching the five chair leg tubes to the
Place the gaslift and decorative
base with ten chair leg screws before
cover in the middle hole of the
inserting the wheels(Tap the screw
feet of the chair;
with a T-wrench and then tighten it);
4
5
Place the cushion, chassis and
Attaching the handrail to the
footrest assembly in line with the
handrail bracket with four
chassis holes and apply the air
M6*30 screws, spring spacers
pressure bar;
and small shims and handrail
tube spacers;
Attach the
seat back
with 2 x M6*
16 screws
7
8
Insert the headrest into the
The armrests are first attached to the
back linkage with four M8*78 screws
back of the chair and attach it
and four big shims, then the seat
with 2 M6*16 screws;
back and chassis tail plate are
Put the back trim cover on and
attached with three M8*20 screws and
the chair is complete.
three big shims;
1.One chair can only bear one person's weight;
Pls read the Safety
2.Please use on the flat floor;
Instructions below
3.Not allowing the child under 5 years old to sit on the chair alone;
carefully.
4.Please don't sit on the armrest, in case cause some danger;
5.Do not stand on the chair or use it as a ladder or footsteps;
6.Please don't put overweight on the chair, or used as trolley;
7.Don't use sharp or hooked objects to scrape the chair and do not get it close to the fire;
8.For your safety, no disassembly to the gaslift is allowed.
01
(The size will be according to regular measurements )
3
Connect the mechanism and the cushion
with 4 mechanism screws(M6*14) with
small shims, be reminded to distinguish
the fronnt and rear of the merchansim
before tightening the screws.
6
Insert the seat back into the
chassis tailpiece of the cushion,
chassis and footrest assembly
Put the seat
back trim
cover on
Functions
The front
Backrest can be adjusted
up or down in 4 positions
Raise up the handle to adjust
扶手可上下左右
the up and down of the chair.
Pull out the handle to adjust
the three angles of recline,
push in to lock the recline angle
Parts list
Wheels: 5 pcs
Armrests: 1 pair
Big shim:7+1pcs
Small shim:8+1pcs
Headrest screws:
M6*16 (2+1pcs)
0
1
Notice: Before installation, pls classify the screw, measure the screw lengh for easy assemble
(The size will be according to regular practice)
Adjustable headrest
with lift and swivel
调节
(The size will be according to regular measurements; One more as a backup )
General Accessories
Chair leg tubes: 5pcs
Base: 1pc
Seat cushion*chassis
Armrest brackets: 1 pair
assembly: 1 pc
Chair leg screws
M6 spring spacer:
（M6*12）:10+1 pcs
4+1 pcs
Armrest tube
Seat back fixing screws
spacers: 2 pcs
(M8*20): 3+1 pcs
Mechanism screws:
1 T-wrench
M6*14（4+1pcs）
2
3
4
5
6
Armrests adjustable upwards,
inward/outward rotation of armrest angle,
forward/backward adjustment
Pneumatic bar: 1pc
Headrest: 1pc
Seat back: 1 pc
1 Mechanism
Armrest screws
Armrest bracket screws
(M6*30): 4+1pcs
(M8*78): 4+1pcs
Hexagonal
Seat back trim
spanner: 1pc
cover: 1pc
Decorative cover
A pair of gloves
7
8
9
10
cm
02
Publicidad
