Unpacking And Inspection - Simer 2925B Manual Del Usuario

General Safety Information
DESCRIPTION
The Simer Laundry Tray System, Model Number 2925B, is
ideal for home wastewater removal from beautician or
utility sinks and wet bars, and for drain water transfer from
air conditioners or dehumidifiers. 1/4 HP submersible
pump unit is equipped with a 3-prong grounding-type
power cord. Motor is oil-filled (dielectric oil) and sealed
for cooler running. Upper sleeve/lower ballbearing on
motor shaft never need lubrication. Automatic reset ther-
mal protection.
SPECIFICATIONS
Power supply required ...................................115V, 60 Hz.
Liquid temp. range..........................................32° to 130°F
Individual branch circuit required (minimum) ......15 Amps
Discharge...........................................................1-1⁄2" NPT

UNPACKING AND INSPECTION

Handle with care. Check items received against packing
list to be sure that all equipment has been received.
Inspect for shipping damage. If found, file claim with carri-
er immediately.
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give many
years of trouble-free service when correctly installed,
maintained, and used. However, unusual circumstances
(interruption of power to the pump, dirt/debris in the
sump, flooding that exceeds the pump's capacity, electri-
cal or mechanical failure in the pump, etc.) may prevent
the pump from functioning normally. To prevent possible
water damage due to flooding, consult your dealer about
installing a high water alarm. See the "Troubleshooting
Chart" in this manual for information about common
sump pump problems and remedies. For more informa-
tion, see your dealer or call customer service.
1. Know the pump application, limitations, and potential
hazards.
2. Disconnect power before servicing.
3. Release all pressure within system before servicing any
component.
PERFORMANCE
Model HP
2925B 1/4
SPECIFICATIONS
Motor
Full Load
HP Amps
1/4 8.5
For parts or assistance, call Simer Customer Service at
GPH of Water @ Total Lift
5' 10'
2280 1620
Switch Setting
On Off
8" 3-1/2"
4. Drain all water from system before servicing.
5. Secure discharge line before starting pump. An unse-
cured discharge line will whip, possibly causing per-
sonal injury and/or property damage.
6. Check hoses for weak or worn condition before each
use, making certain that all connections are secure.
7. Periodically inspect system components. Keep free of
debris and foreign objects. Perform routine mainte-
nance as required.
8. Provide means of pressure relief for pumps whose dis-
charge line can be shut-off or obstructed.
9. Personal Safety:
a. Wear safety glasses at all times when working with
pumps.
b. Keep work area clean, uncluttered and properly
lighted – replace all unused tools and equipment.
c. Keep visitors at a safe distance from work area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter keys.
10. When wiring an electrically driven pump, follow all
electrical and safety codes that apply.
11. This equipment is only for use on 115 volt (single
phase) and is equipped with an approved
3-conductor cord and 3-prong, grounding-type plug.
To reduce risk of electric shock, pull plug
before servicing. This pump has not been investigated for
use in swimming pool areas. Pump is supplied with a
grounding conductor and grounding-type attachment plug.
Be sure it is connected only to a properly grounded
grounding-type receptacle. Where a 2-prong wall recepta-
cle is encountered, it must be replaced with a properly
grounded 3-prong receptacle installed in accordance with
codes and ordinances that apply.
12. All wiring should be performed by a qualified
electrician.
13. Make certain power source conforms to requirements
of your equipment.
15'
660
Top
Height Width
13-3/4" 15-1/8"
1-800-468-7867 / 1-800-546-7867
No flow at
this lift
18'
Bottom
Width Weight
12" 30 lbs.
2