JBM 52241 Manual De Instrucciones página 5

REF. 52241
IMPORTANT! Ensure the locking mechanism (F) is se-
cured through the nearest location hole on the inner
member to prevent an unintentional lowering of the
wheel while being handled.
7. With the wheel nuts secured, the wheel can now
be safely carried away on the wheel changer.
8. Put the pump lever (C) into the socket (K), the
whole machine can be pushed to move.
Unloading the wheel changer
When the wheel is located on the wheel studs and se-
cured with wheel nuts and has been moved to a place
for storage, the wheel can be released.
1. Loosen the clamp support arm (E) by releasing the
adjustment clamps (I and J).
2. Lift and release the locking mechanism (F).
3. Release the lowering pedal (A) from the safety
device (B) and then press down the lowering pe-
dal. Pump apart the wheel changer with the pump
lever (C).
TECHNICAL SPECIFICATIONS
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,5T
Lifting range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0-770mm
Total length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1270mm
Total width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 990mm
Total height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1340mm
Maximum wheel diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200mm (86")
Minimum wheel diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000mm (39")
Maximum wheel width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120kg
PRODUCT OVERVIEW
4. Adjust the wheel support arm (E) so that it does
not catch on the top of the wheel before maneuve-
ring the wheel changer clear of the wheel.
MAINTENANCE
You must refill the hydraulic oil every 8 working hours:
• Pump the wheel changer unit apart until the lifting
rollers are to their widest possible position.
• With the unit at its widest possible reach, remove
the refill screw (G) and top-up the oil.
• Re-filling is best carried out using a measuring jug
with a flexible spout or an oil can.
• The oil used should be equivalent to hydraulic oil
quality ISO VG15.
A
B
C
D
E
F
G
H
I
J
K
L
M
· 5 ·
Lowering pedal
Safety device
Pump lever
Vertical wheel support
handle
Clamp support arm
Locking mechanism
Oil reservoir access
Pin
Height adjustment clamp
Width adjustment clamp
Pin
Handle
Roller table