Publicidad
Idiomas disponibles
Idiomas disponibles
t
LED Illuminated Tree
Operating Manual:
Please read the attached operating manual thoroughly before startup.
Please retain manual and packaging for future reference, as these contain
important information.
Should this appliance be passed on to a third party, then this operating
manual must be included.
Safety Instructions:
This is a decoration article and not a toy for children! Please keep out of
the reach of children.
This article is not suitable for room illumination and it is only for decoration
purpose.
The light source of this article is not replaceable; when the light source
reaches its end of life the whole article shall be replaced.
This article is for indoor use only; do not use outdoors!
This article must not be electrically connected with another article.
Avoid damage to the power cable through squashing and contact
with sharp edges.
Please note that the mains plug and the connecting cable are not to be
damaged. If any damage occurs the article must not be used anymore.
Plug and power cable are not replaceable.
Place the power cable and any extension cable in such a manner that
nobody will stumble upon them or pull on them unintentionally.
The flexible connection conduit of this article cannot be exchanged or
repaired. Should the conduit become damaged, the article must be
destroyed.
Do not connect this article to the supply while it is in the packing unless the
packing has been adapted for display purpose.
Before connecting to the mains, please ensure that available mains voltage
and type are corresponding to the data on the transformer's rating plate.
The article is classified as protection class III and should be
operated only in connection with the provided transformer.
Do not expose the transformer to extreme temperatures.
Always pull by the mains plug, not by the cable.
Do not use in the vicinity of water. Risk of electric shocks!
Not to be operated in vicinity of gas or electric heaters, open fires, candles
or other heat sources.
Never try to repair this article yourself. For servicing and repair, contact a
specialist dealer or a qualified operator.
Please remove the plug from the mains socket if article will not be used for
extended periods of time.
This transformer corresponds to protection class II and should
therefore not be connected to a protective earthing conductor.
Please check for damages prior to each use of the article.
Do not hang any objects on the article.
Do not hang the article on its power cables; please use the textile strings or
the thread guides provided, if available.
Insert the connector plug of the article in the corresponding socket of the
transformer and tighten the coupling nut of the connector plug. Please
check that the sealing is installed and correctly set.
Make sure to follow the correct polarity of the connector plug when
inserting on the socket of the transformer.
Protect the article from dust, humidity and extreme temperatures.
Do not cover the article with other objects.
Do not step on the article!
Keep the article far from easily inflammable materials (e.g. curtains).
The lamps are not replaceable!
ASSEMBLY AND INSTRUCTIONS FOR USE
The tree comes in 3 individual sections (lower section, middle section and top
section) and will sit on a metal stand.
1. After unpacking the product, locate the lower stem of the tree on the metal
stand, screw in the three bolts. Then place the assembled base and lower
section of the tree in an upright position, on a at level surface.
2. It is recommended that you now arrange the lower section branches to your
own preferred display.
3. Locate the middle section of the tree and connect this to the hole on the
upper end of the already assembled lower section.
4. Locate the top section of the tree and connect this to the hole on the upper
end of the already assembled middle section of the tree.
5. The light chain is an integral part of each section of the tree and the
sections of the light chain are joined by connectors. Please ensure that the
connectors are pushed fully in place and the securing plastic ring is then
screwed up tightly.
6. Connect the end of the supply cable to the socket on the low voltage
transformer and then connect the 2-pin transformer to your indoor mains
supply for use.
Technical Data:
Transformer: JT-DC31V3.6W-E4-IP44
Input: 220-240 V~, 50-60 Hz, 0.10 A
Output: 31 V
, 3.6 W
200 LEDs, 3.6 W, warm white
Cleaning and Maintenance:
Pull the mains plug out from the socket before cleaning and let this article
cool down sufficiently.
Clean the article with a soft cloth and with some mild cleaning solvent if
necessary. Do not use petrol or solvents at all, as the materials can be
damaged.
Environmental Protection
Discarded electric appliances are recyclable and should not be discarded
in the domestic waste! Please actively support us in conserving resources
and protecting the environment by returning this appliance to the
collection centres.
Warranty
A statutory warranty applies for this product.
Damages caused by wrong treatment or operation, by false placement or storage,
improper connection or installation, as well as force or other external influences are
not covered by this warranty. We recommend careful reading of the operating
instructions as it contains important information.
Note:
1.
In case this product does not function correctly, please firstly check if there are
other reasons, e.g. for electrical appliances interruption of the power supply, or
generally incorrect handling are the cause.
2.
Please note that, where possible, the following documents or rather
information should be provided together with your faulty product:
- Purchase receipt
- Model description/Type/Brand
- Describe the fault and problem as detailed as possible
In the case of a claim for guarantee or defects, please contact the seller.
GWL 8/14 EN
Model No.: IGT200EV1
180 cm
300 cm
65 cm
QA23-0000000192
MCC Trading International GmbH
Schlüterstraße 5
40235 Düsseldorf
Germany
230425
Made in China
Publicidad
