Publicidad
Idiomas disponibles
Idiomas disponibles
- after contact with foreign objects
- if the machine begins to vibrate
strangely
• Always ensure that the ventilation open-
ings are kept free of foreign objects.
• Always maintain your balance to stand
securely on slopes. Walk, don't run.
• Warning! Do not touch moving danger-
ous parts before the machine has been
switched off and the moving dangerous
parts have come to a complete standstill.
• A tingling feeling or numbness in the
hands is sign of excessive vibration.
Limit the operating time, take sufficiently
long work breaks, distribute the work
between several people or wear anti-
vibration gloves when using the tool for
extended periods
Before starting
Safety key
(Fig. 2)
Due to the latest safety regulations - for service works
with an open device - this machine is equipped with a
safety key, (Fig. X). This must always remain inserted
during normal use. Without this safety key the machine
cannot be put into operation. It is only removed when a
service technician opens the device, in order to prevent
the machine from being switched on inadvertently and a
risk of injury arising.
Charging the battery
Safety Instructions:
The tool is delivered with the lithium-ion battery charged.
However, we recommend recharging the battery before
the tool is operated for the first time.
- Use the included charging unit for charging the battery
only. It is specially designed to match the tool's battery.
- Never use other charging unit. This will result in fire
and/or explosion hazard!
- Always keep the charging unit clear of rain or moisture.
Hazard of electric shock! - Never charge the battery
in the open without protection, always choose a dry,
protected place.
- Never try to charge third-party batteries with this charg-
ing unit. This will result in fire and/or explosion hazard!
- Check the housing, plug and cable for damage before
each use of the charging unit. Do not use the unit if
you detect damage.
- Do not open the charging unit by force. In case of a
defect, the charging unit must be replaced.
- The charging unit heats up during the charging pro-
cess. Do not place the unit on a flammable surface or
operate it in a flammable environment. Fire hazard!
GB | Operating Instruction
- Never open the battery cells. Hazard of short circuits!
- In case of damage to the battery, hazardous vapours or
fluids may escape. In case of incidental contact flush
with water and seek medical advice immediately. The
fluid may have irritating or caustic effects on the skin.
- Protect the battery from heat, intense insolation and
fire. Explosion hazard!
Charging process:
To charge the battery connect the charging unit to an
electrical socket. Then connect the plug of the charg-
ing cable to the charging socket of the grass and shrub
shears or trimmer (fig. 3)
The start of the charging process is indicated by the red
control light ("12", Fig. 4). If the battery is completely
empty the charging time is about 6 hours. After the
battery has been fully charged, the electronic control
automatically switches off the charging process. The red
control light then changes its colour to green indicating
the end of the charging process. It is not required to
monitor the charging time.
The charging unit and the handle of the tool heat up dur-
ing the charging process. This is nothing unusual.
Pull the plug of the charging unit if it is not in use.
The tool must never be switched on during the charging
process!
Recharge the battery every time you realise a consider-
able decrease of the tool's cutting performance. The
battery additionally features an electronic total discharge
protection that protects the battery from damage. This
feature switches the battery off if the discharging thresh-
old is reached. Do not switch the tool on afterwards and
make sure to recharge the battery first.
Rotary handle
For ergonomic use the handle of the shears can be
rotated 90° to the left or right.
After activating the locking mechanism (11) the handle
can be adjusted 90°. Ensure that the locking mechanism
is re-engaged before placing the shears in service again.
Usage and installation of the telescopic push
handle
The telescopic push handle allows you to work comfor-
tably, stood in an upright position.
1. To install the push handle, push the lock (16) and in-
2. The push handle can be adjusted by up to 90 de-
3. To change the length of the push handle, undo the
GB-7
(Fig. 5)
sert the end piece into the corresponding receptacle
underneath the handle (Fig. 6). Make sure that the
push handle engages properly.
grees thanks to its swivel joint. Press the locking
knob (13) and set whatever angle you desire (Fig.
7). Make sure that the swivel joint engages again
properly.
quick release (13) by turning it anticlockwise. Set
Publicidad
