Publicidad
EN - USER MANUAL
INSTALLATION
Pairing a new device with keyboard in Bluetooth mode
• Move the ON/OFF switch located at the bottom of the keyboard to
• Turn ON Bluetooth in device which you want to pair with the keyboard
• Hold the keys FN + BT1 | BT2 | BT3 for 5 seconds to enter into pairing mode. The. LED diode will start flashing rapidly
• Then go to the Bluetooth settings on your device and select from the list Thor 230 TKL
• After successful pairing, the LED on the keyboard will stop flashing
• The keyboard is ready for use
Note: The keyboard can be paired with up to 3 devices, that you can switch by pressing the keys FN + BT1|BT2|BT3.
Connecting the keyboard with the previously paired device
• Turn ON Bluetooth on your device that you have previously paired with the keyboard
• Turn ON or wake up the keyboard from hibernation
• Select required device by short press FN + BT1|BT2|BT3
• The keyboard will automatically connect with the device
Note:
• The device is equipped with intelligent technology for energy management. When the keyboard enter into hibernation (sleep)
mode, press any key for its revival.
• The keyboard is equipped with an ON/OFF switch to save the battery power when not in use for longer period.
Connecting the keyboard via USB receiver
• Move the ON/OFF switch located at the bottom of the keyboard to
• Connect included USB receiver to a free USB port on your device
• The operating system will automatically install the required drivers
• Press FN + 2.4G buttons to switch into connection mode 2.4 GHz
• After successful pairing, the LED on the keyboard will stop flashing
• The keyboard is ready for use
Troubleshooting: If you have trouble connecting the keyboard with the USB receiver, perform the pairing procedure. Disconnect
the USB receiver and hold down FN + 4 buttons for about 5 seconds. LED diode will start flashing rapidly. Reconnect the USB
receiver and the keyboard should pair automatically with the USB receiver.
Wired connection via USB cable
• Move the ON/OFF switch located at the bottom of the keyboard to
• Turn ON your computer or other compatible device
• Connect the cable to a free USB port on your computer, it is necessary to wait about 15 seconds for the first connection until
the drivers are fully installed.
• The keyboard includes software that allows you to set up advanced features, if you want to use these features, you need to
download and install the software from our website www.genesis-zone.com
• Open the installation folder and then double-click the setup.exe file.
• Follow the instruction to install the program.
• After a successful installation, the software icon appears on the main bottom panel. Double-clicking the icon opens the
settings interface.
Note: The software communicates with the keyboard only through the USB cable. All saved settings will be stored in the keyboard
memory even after disconnecting the cable and switch to wireless mode.
CHARGING THE BATTERY
• Connect the included USB-C cable to the keyboard
• Connect USB plug to a suitable power source (max. output DC 5V 0,5A)
• When the battery is fully charged, the LED indicator will change to green color.
Note: When the battery reach the low level the LED indicator will starts flashing, then the keyboard will enter into energy saving
mode and turn off the backlight.
Caution: Please charge the battery every 3 months, if you do not use the keyboard for a long time. Long-term storage of the
keyboard with low battery level, or using the chargers with power over 5V 0,5A may damage the battery.
1. REPLACING SWITCHES
• Remove the keycap by pulling up vertically
• Install a metal clamp under the switch body in place showed on the figure
• Push the clamp arms to the switch body and simultaneously pull up vertically
4
|
or
position
or
position
position
• Insert vertically replacement switch into the holes on the PCB board and gently push down
• Insert the keycap and connect the keyboard to the computer
Note: If the switch does not work after replacement, check if the legs of switch are installed correctly in the holes on the PCB
board or have not been bent.
2. BACKLIGHT BRIGHTNESS
To change the backlight brightness level press keys Fn + Arrow Up/Down.
3. SPEED OF BACKLIGHT EFFECTS
To change the speed of backlight effects, press keys Fn + Arrow Left/Right
4. BACKLIGHT COLOR CHANGE
To change the backlight color, press keys Fn + Del
5. BACKLIGHT MODE CHANGE
Press the keys Fn + Ins to change between 20 backlight modes.
6. CUSTOM BACKLIGHT MODE
Custom mode allows to set the individual illumination of each key.
• Select available custom mode by pressing Fn + 8
• Press Fn + 9 to start recording. Led indicator will start flashing
• Press any keys you want to backlight (for each key you can choose 1 of 7 predefined colors by pressing same key in loop)
• Press Fn + 9 to finish recording and save settings. Led indicator will stop flashing
7. RESTORE FACTORY SETTINGS
All saved settings can be easy restored to default settings by pressing the keys [FN+ESC].
To restore factory settings, hold the keys [FN+ESC] for 5 seconds.
8. ARROW FUNCTION CHANGE
Press the keys FN + W for to swap arrow function with W, A, S, D keys function.
9. BATTERY LEVEL INDICATOR
To check battery level press the keys FN + Enter.
Illumination of particular keys will indicate battery level according to the formula 1 = 10%, 2 = 20% ...
FR - MANUEL DE L'UTILISATEUR
INSTALLATION
Appairage d'un nouvel appareil avec le clavier en mode Bluetooth
• Faites glisser l'interrupteur Marche/Arrêt au bas du clavier en position
• Activez Bluetooth sur l'appareil que vous souhaitez coupler avec le clavier
• Maintenez les touches FN + BT1 | BT2 | BT3 pendant 5 secondes pour entrer en mode d'appairage. La LED va commencer à
clignoter rapidement
• Ensuite, allez dans les paramètres Bluetooth de votre appareil et sélectionnez Thor 230 TKL dans la liste
• Une fois l'appairage réussi, le voyant du clavier cessera de clignoter
• Le clavier est maintenant prêt à l'emploi
Attention: Le clavier peut être appairé à jusqu'à 3 appareils qui peuvent être commutés en appuyant sur les touches FN BT1 |
BT2 | BT3.
Connexion du clavier à un appareil précédemment apparié
• Activez Bluetooth sur l'appareil qui a déjà été appairé avec le clavier
• Activez le clavier ou ou sortez-le l'hibernation
• Sélectionnez l'appareil souhaité en appuyant brièvement sur FN BT1 | BT2 | BT3
• Le clavier se connectera automatiquement à l'appareil
Note:
• L'appareil est équipé de technologies de gestion intelligente de l'énergie. Lorsque le clavier passe en mode hibernation (veille),
appuyez sur n'importe quelle touche pour le réactiver.
• Le clavier est équipé d'un interrupteur Marche/Arrêt pour économiser la pile lorsqu'il n'est pas utilisé pendant une longue
période.
Connexion du clavier via le récepteur USB
• Faites glisser l'interrupteur Marche/Arrêt au bas du clavier en position
• Connectez le récepteur USB fourni à un port USB libre de votre appareil
ou
ou
|
5
Publicidad
