Ego Power+ BCX4500 Manual Del Usuario página 9

ASSEMBLY
WARNING:
If any parts are damaged or missing, do
not operate this product until the parts are replaced. Use
of this product with damaged or missing parts could result
in serious personal injury.
WARNING:
Do not attempt to modify this product or
create accessories not recommended for use with this line
trimmer. Any such alteration or modification is misuse and
could result in a hazardous condition leading to possible
serious personal injury.
WARNING:
To prevent accidental starting that could
cause serious personal injury, always remove the battery
pack from the machine when assembling parts.
WARNING:
When the machine is equipped with
brush cutter head, the safety barrier bar shall be mounted.
MOUNTING THE GUARD (FIG. B1 & B2)
WARNING:
Always wear gloves when mounting or
replacing the guard. Take care of the blade on the guard
and protect your hand from cutting.
WARNING: N
ever operate the machine without
the guard firmly in place. The guard must always be
on the machine to protect the user! When the guard is
fixed, never attempt to remove or adjust the guard, if
a replacement is needed, it should be performed by a
qualified service technician!
NOTICE:
There are two kinds of guards compatible with
this machine. Only the guard with icon
with line trimmer head and must NOT be used with brush
cutter head. Be careful to choose the correct guard when
using the machine.
Loosen and remove the two bolts from the guard, align
the guard mounting holes with the assembly holes and
then lock the guard onto the shaft base with the two bolts,
together with two spring washers.
WARNING:
Make sure the guard is fixed according to
Fig. B1 & B2, any reverse fixing will cause great danger!
ADJUSTING THE BIKE HANDLE
1. Stop the motor and remove the battery pack from the
machine, if installed.
2. During shipping, the bike handle is mounted on the
shaft as shown in Fig. C1.
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER/BRUSH CUTTER — BCX4500
3. Loosen the wing bolt on the bracket and then lift the
bike handle 180° around the shaft as shown in Fig.
C2.
4. Turn the handle 90° COUNTERCLOCKWISE to make
it face the trimmer head (Fig.C3).
5. Tighten the wing bolt to secure the bike handle in
place.
WARNING:
Only start the tool when the bike handle is adjusted
perpendicular to the pole and the operator holds it
with both hands.
REPLACE THE TRIMMER HEAD WITH THE BRUSH
CUTTER HEAD
1. Remove the battery pack from the machine
2. Rotate the trimmer head to align the slot in the flange
with the shaft-locking hole in the gear case and
insert a stabilizer into the hole (Fig. D1).
3. Rotate the trimmer head CLOCKWISE to remove it
from the motor shaft (Fig. D1 & D2).
4. The blade is shipped with a sheath. Before mounting
the blade onto the brush cutter, the sheath should be
removed from the hook on the sheath (Fig. D3).
NOTICE:
To protect against injury, you have to wear
gloves prior to any operation with the 3-tooth blade.
5. Mount the inner flange and flange cover into its
place, if they had separated from the shaft (Fig. D4).
6. Mount the blade onto the motor shaft, ensuring
that the surface of the blade is flush with the
surface of the inner flange bulge. Mount the outer
can be used
flange and the nut (Fig. D5). Finger-tighten the nut
COUNTERCLOCKWISE.
7. Position the gear case against a solid surface for
support. With one hand hold the brush cutter shaft
and the other hand grasp a 16 mm socket wrench
(not included) to tighten the nut COUNTERCLOCKWISE
(Fig. D6).
8. Remove the line trimmer guard by loosening the two
bolts with washers (Fig. D7).
9. Install the brush cutter guard (not included) with the
two bolts and washers from the line trimmer, the
same way as line trimmer guard (Fig. D8).
NOTICE:
When the machine is equipped with the brush
cutter head, be carefully to choose the correct guard.
Risk of serious personal injury.
EN
9