Publicidad
Idiomas disponibles
Idiomas disponibles
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
8
Assembly
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
WARNING
Danger of personal injury!
Never use the cordless leaf vacuum/blower with only
one assembled suction tube part. After the three-piece
suction tube has been put together, it must not be dis-
mantled again into individual parts.
8.1
Fitting the middle blast/suction
tube (17) (Fig. 3)
Note:
There is a safety contact in the motor housing. If this is
not activated during assembly, the product may not start.
Ensure correct assembly.
1. Insert the middle blast/suction tube (17) into the motor
housing (18).
2. Secure the middle blast/suction tube (17) at the top
with the screw (17a).
3. Secure the centre blast/suction tube (17) on the side
with a screw (16a). Use a Phillips screwdriver*.
* = not included in the scope of delivery!
8.2
Fitting the front blast/suction tube
(16) (Fig. 4)
1. Place the front blast/suction tube (16) on the middle
blast/suction tube (17).
2. Secure the front blast/suction tube (16) with a screw
(16a). Use a Phillips screwdriver*.
* = not included in the scope of delivery!
8.3
Assembling/removing the
collection bag (12) (Fig. 5)
1. Place the collection bag inlet with locking device (11)
on the ejection opening (19). Make sure that it engag-
es properly.
2. Hook the rear collection bag eye (7) into the hook at
the rear (6).
3. Hook the front collection bag eye (13) into the front
hook (14).
20 | GB
4. Remove the collection bag (12) in reverse order.
8.4
Fitting the carrying strap (20) (Fig.
1, 2)
Note:
Never wear the carrying strap diagonally across your
shoulder and chest, but only on one shoulder, this allows
you to quickly remove the product from your body in the
event of danger. Open the buckle to be able to open the
catch quickly in the event of an accident.
1. Place the carrying strap (20) over one shoulder.
2. Adjust the length of the belt so that the carabiner hook
(20a) is approx. 10 cm beneath the hip.
3. Open the carabiner hook (20a) of the carrying strap
(20).
4. Clip the carabiner hook (20a) into the fastening eye of
the carrying strap (2).
9
Before commissioning
ATTENTION
Always make sure the product is fully assembled
before commissioning!
9.1
Select operating mode (Fig. 6)
ATTENTION
The operating mode may only be changed at a stand-
still.
The operating mode can be selected using the mode se-
lector lever (10).
10 Operation
The cordless leaf vacuum and blower has a fan for the
suction and blowing functions. During suction, the
sucked-in leaves are shredded to reduce volume, blown
through the ejection port and collected in the collection
bag. In blowing mode, the leaves can be quickly blown to-
gether or blown away from hard-to-reach places.
Please refer to the following descriptions for the function
of the controls.
Note:
A leaf blower is not a wet vacuum cleaner!
Please avoid vacuuming wet materials (leaves, dirt as
well as twigs, branches, pine cones, grass, soil, sand,
bark mulch/chippings, etc.).
Do not vacuum on damp or wet lawns, grass or mead-
ows, as incorrect use may lead to blockages in the shred-
ding chamber and thus to reduced performance.
www.scheppach.com
Use as a leaf vacuum.
Use as a leaf blower.
Publicidad
