EINHELL GE-SR 18/22 Li Manual De Instrucciones página 14

4. Technical data
Motor power supply: ............................ 18V
No load speed RPM: ............................... 330-700
Max. coverage area per load: ........... 16,145 sq. ft.
Spreading width: ......................................5 - 20 ft.
Filling volume /container bulk weight (approx.): ....
................................................... 6 Gallon / 66 lbs.
Weight (Tool Only): ...................................14.3 lbs
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
4. Risk of eye damage if essential safety
goggles are not worn.
Anl_GE_SR_18_22_Li_SPK7_NA.indb 14 Anl_GE_SR_18_22_Li_SPK7_NA.indb 14
EN
5. Before starting the equipment
The machine is supplied without batteries
and without a charger!
Follow the instructions step by step and refer to
the pictures when assembling.
5.1 Fitting the wheels on the foot (Fig. 4-7)
Push a washer (Item 21), a wheel (Item 10) and
another washer (Item 21) onto the axle (Item 25).
Then press the straight part of the wheel lock
(Item 20) through the axle hole (Item 26) and
secure the wheel. Fit the second wheel in the
same way.
5.2 Fitting the wheel caps (Fig. 8)
Place the wheel caps (Item 11) on the wheels
(Item 10) so that the clips (Fig. 3/Item 27) of the
wheel caps and the recesses (Fig. 3/Item 28) of
the wheels are aligned with each other. Press the
wheel caps onto the wheels.
5.3 Fitting the foot on the spreader material
compartment (Fig. 9)
Insert the base tubes (Item 29) in the base tube
mounts (Item 30) and fasten with the short self-
tapping screws (Item 24).
5.4 Fitting the spacers on the long handle
tube (Fig. 10)
Important! Be sure to observe the correct
alignment of the spacers (Item 15)! The cable
holder (Item 31) must be on the right-hand side.
Push the spacers (Item 15) onto the two long
handle tubes (Item 6) and use the short self-
tapping screws (Item 24) to secure to the
respective long handle tube (Item 6).
5.5 Fitting the long handle tubes on the
spreader material compartment (Fig. 11-
12)
Important! Be sure to observe the correct
alignment of the screws!
Insert both long handle tubes (Item 6) in the tube
mounts of the spreader material compartment
(Item 9) and secure with the M6 screws, washers
and cap nuts (Item 23).
5.6 Fitting the handle on the long handle tube
(Fig. 13-14)
Insert the tube mounts of the operating unit (Item
1) into both long handle tubes (Item 6), line up the
operating unit mounts (item 32). Then place the
- 14 -
09.04.2024 11:22:20 09.04.2024 11:22:20