Publicidad
Idiomas disponibles
Idiomas disponibles
E-SERIES PRO XP 125-15
Symbols used in this manual
WARNING!
Denotes impending danger. Non-observance of this warning
may result in death or extremely severe injuries.
CAUTION!
Denotes a possibly dangerous situation. Non-observance of
this warning may result in slight injury or damage to property.
NOTE
Denotes application tips and important information.
Symbols on the power tool
Before switching on the power tool, read the
operating manual!
Wear goggles!
Protection class II (completely insulated)
Disposal information for the old machine
(see page 14)!
For your safety
WARNING!
Before using the polisher, please read and follow:
–
these operating instructions,
–
the "General safety instructions" on the handling of power
tools in the enclosed booklet (leaflet-no.: 334.480),
–
the currently valid site rules and the regulations for the
prevention of accidents.
This polisher is state-of-the-art and has been constructed in
accordance with the acknowledged safety regulations.
Nevertheless, when in use, the power tool may be a danger
to life and limb of the user or a third party, or the power tool
or other property may be damaged. The polisher may be
used only
–
as intended,
–
in perfect working order.
Faults which impair safety must be repaired immediately.
Intended use
This hand-operated orbital polisher is designed
–
is designed for industrial applications,
–
for all types of polishing work, e.g. paintwork on vehicles,
furniture and metal surfaces, etc. with polishing sponge,
lambswool and wool pads,
–
for use with polishing tools which are permitted to run at
a speed of at least 500 r.p.m.
Safety instructions for polishing
WARNING!
Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to
follow all instructions listed below may result in electric
shock, fire and/or serious injury. Save all warnings and
instructions for future reference.
This power tool is intended to function as a polisher.
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Operations such as grinding, sanding, wire brushing,
or cutting-off are not recommended to be performed
with this power tool. Operations for which the power tool
was not designed may create a hazard and cause
personal injury.
Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed can
break and fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted by
flanges, the arbour hole of the accessory must fit the
locating diameter of the flange. Accessories that do not
match the mounting hardware of the power tool will run out
of balance, vibrate excessively and may cause loss of
control.
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of the
rotating accessory and run the power tool at maximum
no-load speed for one minute. Damaged accessories
will normally break apart during this test time.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying debris
generated by various operations. The dust mask or
respirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
11
Publicidad
