Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
While working, hold the tool in such a way that no
u
injuries can be caused to the head or to the body in
the event of a possible recoil due to a disruption in
the energy supply or hard areas within the work piece.
Never actuate the fastener driving tool into free space.
u
In the work area, carry the tool at the workplace using
u
only one handle, and never with the trigger actuated.
Consider the conditions in the work area Fasteners
u
can penetrate thin work pieces or slip off corners and
edges of the work piece, and thus put people at risk.
Do not drive fasteners close to the edge of the work
u
piece.
Do not drive fasteners on top of other fasteners.
u
Always assume that the tool contains fasteners.
u
Careless handling of the nailer can result in unexpected
firing of fasteners and personal injury.
Do not point the tool towards yourself or anyone
u
nearby. Unexpected triggering will discharge the fastener
causing injury.
Do not actuate the tool unless it is placed firmly
u
against the workpiece. If the tool is not in contact, the
fastener may be deflected away from your target.
Disconnect the tool from the power source when the
u
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
Do not use this tool for fastening electrical cables.
u
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
26
(Original instructions)
Labels on tool
The following symbols are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Warning! To reduce the risk of injury, the
user must wear ear and eye protection.
Keep hands and body parts clear of immedia-
te work area.
Additional safety instructions for batteries and
chargers
Batteries
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
u
40 °C.
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Do not damage/deform the battery pack either by puncture
u
or impact, as this may create a risk of injury and fire.
Do not charge damaged batteries.
u
Under extreme conditions, battery leakage may occur.
u
When you notice liquid on the batteries Carefully wipe the
liquid off using a cloth. Avoid skin contact.
In case of skin or eye contact, follow the instructions
u
below.
Warning! The battery fluid may cause personal injury or
damage to property. In case of skin contact, immediately rinse
with water. If redness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse immediately with clean
p
water and seek medical attention.
Do not attempt to charge damaged batteries
Chargers
Use your Stanley charger only to charge the battery in
u
the tool with which it was supplied. Other batteries could
burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
u
Have defective cords replaced immediately.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger
u
Publicidad
