Balluff BIS C-830-4-011-A Instrucciones Breves página 4

BIS C-830-4-011-A
Mobile RFID devices - LF plug-in module
About this guide
This guide provides all the necessary information for the
LF plug-in module.
It applies to the following models:
– BIS C-830-4-011-A
Order code: BIS01HE
LF plug-in module for BIS C read/write heads
(70/455 kHz)
Intended use
With the LF plug-in module, Balluff RFID read/write heads
BIS C-323/05-S4 and BIS C-325/05-S4 can be connected
to mobile basic devices of the BIS V-830-3-011-B-00_
series in order to expand them with the RFID function.
The LF plug-in module is intended exclusively for use with
the following products:
– BIS V-830-3-011-B-00_ (basic device of the series)
– BIS C-323/05-S4 (read/write head)
– BIS C-325/05-S4 (read/write head)
Proper function according to the specifications in the
technical data is only assured when the product is used
solely as described in the user's guide and the respective
documents as well as in compliance with the technical
specifications and requirements and only with suitable
original Balluff accessories.
Otherwise, there is deemed to be unintended use.
Unintended use is not permitted and will result in the loss
of warranty and liability claims against the manufacturer.
Reasonably foreseeable misuse
The product is not intended for the following applications
and areas and may not be used there:
– In safety-oriented applications in which personal safety
depends on the device function
– In explosive atmospheres
– In the food contact area
Construction
BIS C-830-4-011-A (LF plug-in
module)
2 nuts (fastening)
BIS C-3_ _ /05-S4 (read/write
head)
BIS C-1_ _ (RFID data carrier)
1 english
BIS V-830-3-011-B-00_
(basic device)
Other applicable documents
A comprehensive user's guide and additional information
about this product can be found at www.balluff.com on
the product page.
Safety notes
Activities such as installation, connection and
commissioning may only be carried out by qualified
personnel.
Qualified personnel are persons whose technical
training, knowledge and experience as well as knowledge
of the relevant regulations allow them to assess the work
assigned to them, recognize possible hazards and take
appropriate safety measures.
The operator is responsible for ensuring that local safety
regulations are observed.
In particular, the operator must take steps to ensure that a
defect in the product will not result in hazards to persons
or equipment.
The product must not be opened, modified or changed. If
defects and unresolvable faults occur in the product, take
it out of service and secure against unauthorized use.
Only original Balluff power supply units may be used for
the operation of the module. The use of unauthorized
components may lead to the destruction of the module or
the basic devices. Do not use the module with an external
device.
The module cannot be installed in the vicinity of heat
sources (e.g. fan heaters) and exposed to direct sunlight,
excessive dust sources or vibrations. Observe ambient
conditions:
– Operating temperature: 0...50 °C
– Storage temperature: −20...+60 °C
In order to avoid overheating, the module cannot be
covered during operation.
Before use check the contacts of the module as well as
the contacts of any connectors for dirt and clean if
necessary. Check the module and any connection cables
for damage. Damaged parts must be replaced.
Function
BIS C-830-4-011-A is a RFID LF plug-in module that
operates at an operating frequency of 70/455 kHz and is
used to read and write Balluff BIS C-1_ _ data carriers in
industrial environments. Mobile basic devices of the
BIS V-830-3-011-B-00_ series can be expanded to a
mobile LF RFID system in conjunction with the LF plug-in
module and a read/write head (BIS C-3_ _ /05-S4).