Publicidad
Idiomas disponibles
Idiomas disponibles
Please visit our website www.stanley.eu/3 for further
information.
Fitting and removing a screwdriver bit or socket
(fig. G, H)
This tool is fitted with a quick release chuck to allow for an
easy exchange of bits.
Warning! Make certain the tool is locked to prevent switch
actuation before installing or removing accessories.
Lock the tool by setting the forward/reverse slider (2) to
u
the centre position.
Insert the bit shaft (11) into the chuck (4) (Fig. G).
u
Note! To remove the bit/socket, pull and hold the chuck collar
(3) away from the front of the tool (Fig. H).
Warning! Use only impact rated sockets. Non-impact sockets
may break and cause a hazardous condition. Inspect socket
prior to use to ensure that it contains no cracks. Use only
impact rated accessories.
Use
Warning! Let the tool work at its own pace. Do not overload.
Selecting the direction of rotation (fig. I)
For tightening, use forward (clockwise) rotation. For loosening,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(2) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
To lock the tool, set the forward/reverse slider into the
u
centre position.
Screwdriving / nut setting
Select the appropriate bit / socket for the screw or nut to
u
be driven.
Select forward or reverse rotation as described above.
u
Hold the tool in line with the fastener.
u
Press the trigger (1)
u
After tightening, check torque with a torque wrench.
u
LED work light
The LED work light (7) is activated automatically when the trig-
ger is depressed. The LED work light will illuminate when the
trigger is partially depressed, before the unit begins running.
Hints for optimum use
Screwdriving
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
u
amount of washing liquid or soap as a lubricant.
Always hold the tool and screwdriver bit in a straight line
u
with the screw.
(Original instructions)
Maintenance
Your Stanley Fat Max tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
V
DC
No-load speed
-1
Min
Beats
BPM
Max. torque
Nm
(PTI Method)
Chuck
mm
capacity
Weight
kg
Charger
SFMCB10
Input Voltage
V
230
AC
Output Voltage
V
18
DC
Current
A
1.25
Battery
SFMCB201
Voltage
18
V
DC
Capacity
Ah
1.5
ENGLISH
SFMCF800
SFMCB11
SFMCB12
SFMCB14
230
230
18
18
1.25
2
SFMCB202
SFMCB204
SFMCB206
18
18
2.0
4.0
18V
0-2800
0-3100
165
6 (Hex)
1.5
230
18
4
18
6.0
9
Publicidad
