OGK urban uki Rear seat Instrucciones De Montaje página 10

ENG
We care about you and your child's safety. Therefore, we
strongly recommend reading the following instructions
and warnings carefully before installing the seat.
Visual instructions on how and where to mount, and how
to use the seat and relevant accessories can be found in
the corresponding chapter and number on pages 3 - 9.
B - Instructions for mounting
1. Put the foot strap through the footstep, and pull to fix
the strap.
2. Assemble the leg protection plates together.
3. While keeping the additional retention system down
(A), mount the leg protection plates to the seat (B).
4. Insert the screws with the lock washer rings through
the mounting block (A). Make sure the protective
material is on the inside of the bolts (B).
5. Fix the mounting block to the frame using the metal
back plate. Make sure the bike frame type is suitable
for the seat mount. The seat cannot be attached to
the seat-post unless allowed by the manufacturer of
the bike.
6. Insert the Carrier to the Mounting block until it "clicks."
7. Loosen the screws of the mounting system (A) and put
it on the carrier (B). The axle of the rear wheel should
fall within the arrows of the mounting system (C).
Check that the point markings of the carrier are within
the clamps (D). Tighten the screws of the mounting
system with maximal 5 Nm of torque (E).
8. While holding the additional retention system (A)
place the seat flat, halfway on the mounting system
(B). While pushing down, slide the seat to the front (C)
until the seat clicks into the mounting system (D). Note
that the seat can be mounted while locked. Check that
the seat is correctly installed by pushing the back of
the seat (E).
9. Make sure that the seat does not slope forward to
avoid your child sliding out of it. The backrest should
slope slightly backward.
10. Put the straps of the additional retention system
around the bike frame (A). Put the strap through the
belt adjuster (B) and secure the loose end with the clip
(C). Check that the belt adjuster is free from the frame
(D). Make sure there is some slack in the strap so the
carrier has space to move (E).
11. Check and adjust the height of the seat (A) and tighten
the screws of the carrier mount to max. 5 Nm of torque
(B). Put the cover over the mounting block and slide it
down until it clicks into place. (C)
To demount the seat:
12. To demount the seat: Remove the additional retention
system (A & B). Use the key to open the lock (C). Push
the safety clip down (D) and pull the fix backward (E)
while holding the safety lock down (E). Take the seat
off the carrier (F). Use the key to lock the seat and
remove the key (G).
13. Push the front of the mounting bracket down (A) and
pull out the carrier (B).
14. To remove the cover, push the lever (A) and at the
same time slide the cover to the top (B).
10
The seat should be installed as close to the saddle as
●
possible.
Make sure to regularly check that the seat and the
●
relevant fasteners are fully tightened and secured.
The seat should only be fitted to a suitable bike, which
●
means that the bike is appropriate for the mounting
of the specific bike seat. We advise you to check
any information supplied with the bike and (where
applicable) the luggage carrier. If it is not available, you
should seek advice from the manufacturer or supplier.
The seat is not suitable for use on a moped.
Check that all parts of the bike function correctly with
●
the seat mounted.
C - Instructions for use
1. To release the belt from the buckle, push points A and
B at the same time and remove the belt (C). Do this for
each side.
2. After placing your child in the seat, place each belt
connector into the buckle. Check that the belt is
securely fastened.
3. Fasten the safety belt firmly but not too tightly; pull
the belt adjuster up (A) and pull on the loose belt end
(B).
4. To loosen the restraining system, pull the belt adjuster
up (A) and pull back (B).
5. Check that the legs of your child have a perpendicular
angle (A). If not (B), adjust the footsteps to the required
height; open the lever on the back of the foot step, (C)
adjust the height, (D) and lock the lever on the back
(E).
6. Ensure your child's feet stay in place by fastening the
foot straps; Pull down and outward on the loose strap
end (A) to open the foot strap. To close the foot strap,
choose the correct height and hook the foot strap to
the footstep (B), fixing it by pulling down (C).
Check whether you are legally permitted to use the
●
seat in the country in which you intend to use it.
Your bike seat is intended for taking your child with
●
you on your bike in an everyday setting. The seat is not
suitable for sporting activities such as mountain biking
or racing.
The seat must not be used with speeds above 25km/h.
●
If you are using a rear seat that is attached to a
●
luggage carrier, make sure that the load capacity
of the carrier is not exceeded. The seat should only
be fitted to luggage carriers that conform to EN ISO
11243:2016.
Do not carry a child that is too young to sit safely in the
●
seat. The seat is approved for children from 9 months
to 5 years old, with a maximum weight of 22 kg and
maximum height of 110 cm.
Only carry children that can sit unaided for an
●
extended period of time, and at least for as long as the
intended bicycle journey. Regardless of age, your child
must be able to hold their head up.
Once you have installed the seat for the first time,
●
make sure to take a brief test ride without and with
your child in a safe and quiet environment.
Check that the bike seat is not too hot in the sun
●
Copyright 2024 by OGK Europe B.V.