Kenmore 10670872990 Manual De Uso Y Cuidado página 6

3. The ice maker is equipped with a built-in water strainer. If
your water conditions require a second water strainer, install it
in the 1/4in. (6.35 ram) water line at either tube connection.
Obtain a water strainer from your nearest appliance dealer.
4. Plug in refrigerator or reconnect power.
TOOLS NEEDED: %6 in. hex-head socket wrench, No. 2 Phillips
screwdriver, flat-head screwdriver, 5/16 in. open-end wrench, flat 2
in. putty knife.
IMPORTANT:
• Before you begin, turn the refrigerator control OFF, unplug
refrigerator or disconnect power. Remove food and any
adjustable door or utility bins from doors.
• If you only want to remove and replace the doors, see the
"Door and hinge removal" and "Door and hinge replacement"
sections.
Door and hinge removal
5/_6"FlexHead Hinge Screw
1. Unplug refrigerator or disconnect power.
2. Open refrigerator door and remove base grille from the
bottom front of the refrigerator (see Base Grille graphic).
3. Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
4. Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the freezer door free from the cabinet.
5. Remove the parts for the center hinge as shown in the Center
Hinge graphic. Lift the refrigerator door free from the cabinet.
6. Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic.
IMPORTANT: If you want to reverse your doors so that they
open in the opposite direction, follow these steps. If you are
not reversing the doors, see "Door and Hinge Replacement".
Door reversal (optional)
(Graphics follow these instructions.)
Door Stop Screw
Door Handle Sealing Screw
Flat-Head Handle Screw
Door Hinge Hole Plug
Cabinet Hinge Hole Plug
Round-Head Handle Screw
Door Handle Seal Screw Front Shoulder Handle Screw
Cabinet
1. Remove 5/lein. hex head hinge screws from handle side and
move them to opposite side (see Graphic 1-1).
2. Remove cabinet hinge hole plugs from cabinet top and move
them to opposite side hinge holes as shown (see Graphic
1-2).
Freezer door
1. Remove freezer handle assembly as shown. Keep all parts
together (see Graphic 2).
2. Remove door hinge hole plug. Move to opposite side as
shown (see Graphic 3).
3. Remove door handle sealing screws. Move to opposite side
of freezer door as shown (see Graphic 4).
4. Remove door stop. Move to opposite side of freezer door as
shown (see Graphic 5).
5. Position freezer handle on opposite side of freezer door.
Assemble handles on door as shown (see Graphic 2).
6. Tighten all screws. Set aside door until hinges and refrigerator
compartment door are in place.
Refrigerator door
1. Remove refrigerator handle bottom trim. For Style 1, remove
screw from bottom of door and slide trim down as shown
(see Graphic 6-1). For Style 2, slide trim down as shown (see
Graphic 6-2).
2. Remove refrigerator handle assembly as shown. Keep all
parts together (see Graphic 6-3).
3. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown (see Graphic 3).
4. Remove door handle sealing screws. Move to opposite side
of refrigerator door as shown (see Graphic 4).
5. Remove door handle seal screw front. Move to opposite side
of refrigerator door as shown (see Graphic 7).
6. Remove door stop. Move to opposite side of refrigerator door
as shown (see Graphic 5).
7. Position refrigerator handle on opposite side of the
refrigerator door as shown (see Graphic 6-3). Drive top two
screws in handle first. Align lower portion of handle and drive
bottom screw.
8. Align refrigerator handle bottom trim. For Style 1, slide trim
into place and attach bottom screw (see Graphic 6-1). For
Style 2, slide trim into place (see Graphic 6-2).
9. Tighten all screws. Set aside refrigerator door until bottom
hinge is installed on product.
Door and hinge replacement
NOTE: Graphic may be reversed if door swing is reversed.
1. Replace the parts for the bottom hinge as shown. Tighten
screws. Replace the refrigerator door.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
2. Assemble the parts for the center hinge as shown and tighten
all screws (see Center Hinge graphic). Replace the freezer
door.
3. Assemble the parts the top hinge as shown (see Top Hinge
graphic). Do not tighten screws completely.
4. Line up the doors so that the bottom of the freezer door
aligns evenly with the top of the refrigerator door. Tighten all
screws.
6