Publicidad
Advanced Features
listening through a Receiver
¦
You can listen to sound through a receiver (i.e Home Theater) instead of the TV speaker.
1. Select Receiver and set to On.
2. Press the
EXIT
button to exit.
✎
If your receiver supports audio only, it may not appear in the device list.
✎
The receiver will work when you have properly connected the optical in jack of the receiver to the
OUT (OPTICAl)
✎
When the receiver (i.e Home Theater) is set to
the TV is displaying a DTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from
the receiver.
✎
nOTE
x
You can only control Anynet+ devices using the TV remote control, not the buttons on the TV.
x
The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
x
The Anynet+ functions do not operate with other manufacturers' products.
Troubleshooting for Anynet+
¦
Problem
Anynet+ does not work.
I want to start Anynet+.
I want to exit Anynet+.
The message 'Connecting to
Anynet+ device...' appears on
the screen.
The Anynet+ device does not
play.
The connected device is not
displayed.
The TV Program cannot be
recorded.
The TV sound is not output
through the receiver.
38
English
BN68-02604C_Eng.indb 38
jack of the TV.
On, you can hear sound output from the TV's Optical jack. When
Possible solution
•
Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
•
Only one receiver (home theater) can be connected.
•
Check if the Anynet+ device power cord is properly connected.
•
Check the Anynet+ device's Video/Audio/HDMI cable connections.
•
Check whether
Anynet+ (hDMI-CEC) is set to On in the Anynet+ setup menu.
•
Check whether the TV remote control is in TV mode.
•
Check whether the remote control is Anynet+ compatible.
•
Anynet+ does not work in certain situations. (Searching channels, operating
(initial setup), etc.)
•
When connecting or removing the HDMI cable, please make sure to search devices again or turn your
TV off and on again.
•
Check if the Anynet+ Function of Anynet+ device is set on.
•
Check if the Anynet+ device is properly connected to the TV and check if the
set to On in the Anynet+ Setup menu.
•
Press the
TOOls
button to display the Anynet+ menu and select a menu you want.
•
Select
View TV in the Anynet+ menu.
•
Press the
sOURCE
button on the TV remote control and select a device other than Anynet+ devices.
•
Press
> Ch
Ch
lIsT, PRE-Ch, and
<,
button operates only when a tuner-embedded Anynet+ device is not connected.)
•
You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
•
Use the remote control when the Anynet+ setting or switching to view mode is complete.
•
You cannot use the play function when
•
Check whether or not the device supports Anynet+ functions.
•
Check whether or not the HDMI cable is properly connected.
•
Check whether
Anynet+ (hDMI-CEC) is set to On in the Anynet+ setup menu.
•
Search Anynet+ devices again.
•
You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may not support
Anynet+ functions.
•
If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a
power failure, please repeat the device scan.
•
Check whether the antenna jack on the recording device is properly connected.
•
Connect the optical cable between TV and the receiver.
FAV.Ch
to change the TV mode. (Note that the channel
Plug & Play (initial setup) is in progress.
DIgITAl AUDIO
Media Play or Plug & Play
Anynet+ (hDMI-CEC) is
2010-09-01
10:03:31
Publicidad
