Bosch GLI 18V-2200 C Professional Manual Original página 13

pressed unintentionally. The rechargeable battery is held in
place by a spring when fitted in the cordless worklight.
Battery charge indicator
Note: Not all battery types have a battery charge indicator.
The green LEDs on the battery charge indicator indicate the
state of charge of the rechargeable battery. For reasons of
safety, it is only possible to query the state of charge when
the cordless worklight is switched off.
Press the button for the battery charge indicator
show the state of charge. This is also possible when the re-
chargeable battery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the rechargeable battery is defective
and must be replaced.
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Bosch Power Tools
Assembly
Putting the Coin Cell into Operation
(see figure A)
Remove the separating film between the coin cell (11) and
the coin cell contact when using the tool for the first time.
The cordless worklight is fitted with a coin cell so that it can
be detected by the mobile device even if no battery
pack (14) is inserted.
or to
Unlock the locking mechanism of the battery cover (2) and
fold back the battery cover (3).
Unscrew the screw of the battery compartment cover (9)
and remove the battery compartment cover (10).
Remove the film from the coin cell contact and reattach the
battery compartment cover with the screw.
Operation
Capacity
Start-up
60–100 %
Setting up
30–60 %
Carefully fold out the stand (5) and place the cordless work-
light on the floor. Make sure it is secure.
5–30 %
0–5 %
Fastening to the tripod
You can use the tripod mount (7) to screw the cordless
worklight onto a tripod.
Tighten the 5/8" screw. Ensure that the tripod has a firm
footing.
Swivelling the Lamp Head (see figure B)
Capacity
The lamp head (4) is attached to the carrying handle (8).
80–100 %
The lamp head can be set to five different positions using the
carrying handle.
60–80 %
40–60 % Switching On/Off
To start up the cordless worklight, press the on/off switch
20–40 %
(1).
5–20 %
To switch off the cordless worklight, press the on/off switch
0–5 %
(1) again.
Adjusting the Brightness
Press the on/off switch (1) briefly to switch on the cordless
worklight with maximum brightness. To adjust the bright-
ness in two stages, hold down the on/off switch (1) until the
required brightness is reached.
Temperature-dependent overload protection
When the permitted operating temperature is exceeded, the
cordless worklight initially reduces the brightness before
switching itself off if required for protection. Let the cordless
worklight cool down and then switch the cordless worklight
back on.
Changing the Coin Cell (see figure A)
Make sure that the battery compartment (12) is not
u
damaged when removing the coin cell.
Make sure that the positive pole of the coin cell faces
u
upwards.
English | 13
1 609 92A 9JN | (06.05.2024)