Descargar Imprimir esta página

GLOBBER ONE K E-MOTION 15 Manual Del Propietário página 6

Ocultar thumbs Ver también para ONE K E-MOTION 15:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 28
STOP
- To stop, keep pressing the rear brake continuously for 3 seconds and wait for
the scooter to stop safely to get off the scooter.
- At any time you can remove your foot from the acceleration sensor to
automatically shut down the motor for example in an emergency. The battery
will automatically turn itself off when the motor is not engaged for more than 10
minutes.
SPEED MODE SELECTION
- When you first press the ON/OFF button, the scooter is by default in "Normal
mode". When the scooter is in "ON" mode, but the motor is not being engaged,
the scooter is in "Standby mode".
- In standby mode, you can switch between the 2 speed modes by pressing the
ON/OFF button.
Mode 1 (default mode): Normal Mode; max speed is 20km/h.
Mode 2: Pedestrian Mode, max speed is 6km/h.
- To switch from "Normal Mode" to the "Pedestrian Mode", press the ON/OFF
button once. The tail light will start flashing in red, showing that the scooter is
now in "Pedestrian mode". The max speed in this mode is 6km/h.
- To switch back to "Normal mode" from "Pedestrian Mode" press the ON/OFF
button again. The tail light will stop flashing, showing that the scooter is now
back in "Normal mode". The max speed in this mode is 20km/h.
5 - CHARGING
When the battery signal light on the deck becomes low, you can
recharge the battery with the specific charger.
Your electric scooter is delivered with a specific charger. Only charge the scooter indoors.
1. To charge your electric scooter, remove the waterproof cap from the port and plug in the
charger. For safety reasons, ensure the charging port is always dry before starting to
charge.
2. Plug the charger into a suitable power source.
3. When LED on the charger is red, the battery is charging.
4. When the signal light changes to green, the battery is fully charged; this will take
approximately 3 hours. You must stop charging it when the signal light turns green;
charging the battery for too long will reduce its lifetime.
6
1
2
The protective cover is used to protect the charging port from splashing water. Be sure to
replace the cap after each charging and before each use.
- Children shall not play the appliance.
- Cleaning and user maintenance should not be made by children without
supervision.
- The charger is specific for lithium battery pack 36V and 2.6AH
(Model No.: 10S1PSCOOTERM26).
- The battery charger has LED indicator: GREEN light indicates the battery is fully
charged or disconnected; RED light indicates the battery is in charging.
- Do not recharge non-rechargeable batteries. It may cause explosion.
- Only use the charger supplied with your electric scooter. Using a charger other than that
supplied will invalidate the warranty.
- To optimise the performances and lifetime of your electric scooter battery, fully charge the
battery before using it for the first time and fully charge it once a month.
- Do not cover the battery compartment or the charger. There must be good ventilation
conditions at all times during charging.
- The charging environment must be clean. Ensure there are no traces of damp or water in
the electric socket before plugging in.
- Ensure you use a standard socket.
- Do not switch on the scooter during charging.
- External LED light: The signal light will turn red when the LED battery has less than 10%
battery remaining. Please use the USB cable provided in-pack to charge the LED light.
When the signal light changes to green, the LED battery is fully charged; this will take
approximately 3 hours. You must stop charging the LED light when the signal light turns
green; charging the battery for too long will reduce its lifetime.
Warning. Do not use the battery or the device in the following cases:
1. The battery gives off a smell or the temperature inside the appliance is too high.
2. Leaks on the deck of the scooter.
If in doubt please contact Globber, contact@globber.com
Important:
- The battery must only be removed and changed by an official Globber repair center. No
attempt should be made to dismantle the product and repair it yourself. Any attempt to do
so will invalidate the warranty.
- In case of battery leakage, do not touch it.
3
4

Publicidad

loading