Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
EN
•
When a suspension device is used, ensure that it is securely fastened. Failure to secure may result in loss of control, unexpected motion,
or dropping of the tool.
This power tool is intended to function as a grinder, sander, or polisher. Read all safety warnings, instructions, illustrations and
•
specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious
injury.
Operations such as wire brushing or cutting-off are not recommended to be performed with this power tool. Operations for which the
•
power tool was not designed may create a hazard and cause personal injury.
•
Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory
can be attached to your power tool, it does not assure safe operation.
The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster
•
than their rated speed can break and fly apart.
•
The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or controlled.
The arbor size of wheels, flanges, backing pads or any other accessory must properly fit the spindle of the power tool. Accessories
•
with arbor holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss
of control.
Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad
•
for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or
install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane
of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break
apart during this test time.
•
Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate,
wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of
filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.
•
Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment.
Fragments of work piece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact
•
hidden wiring or it's own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and shock
the operator.
Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled
•
into the spinning accessory.
•
Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull
the power tool out of your control.
Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling
•
the accessory into your body.
•
Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered
metal may cause electrical hazards.
Do not operate the power tool near flammable materials. Sparks could ignite these materials.
•
•
Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary
•
handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions
or kickback forces, if proper precautions are taken.
•
Never place your hand near the rotating accessory. Accessory may kickback over your hand.
Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite
•
to the wheel's movement at the point of snagging.
•
Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or
bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
Do not attach a saw chain, woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.
•
Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper.
•
Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disk or kickback.
Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose
•
attachment strings. Loose and spinning attachment strings can entangle your fingers or snag on the work piece.
•
Do not use this tool if the actual free speed exceeds the rated rpm by more than 10 percent. Check the free speed of the Grinder before
inserting an accessory, after all tool repairs and after every 8 hours of use. Check speed with a calibrated tachometer, without the abrasive
product installed.
Use only burrs, wheels and similar abrasive accessories with these tools. Use of other accessories may result in serious injury.
•
•
Do not use any wire or grinding wheels with a diameter that is greater than 2 inches (50 mm) with this unguarded grinder, unless
used for internal work and only operated when the work offers protection. Larger diameters should only be used with guarded tools.
Do not use any small cones and plugs and threaded hole pot balls unless the work offers protection and their size does not
•
exceed 3 inches (75 mm) in diameter by 5 inches (125 mm) long. The work should protect from possible injury caused by accessory.
•
Do not use any Type 1 wheels that are larger than 2 inches (50 mm) in diameter or more than 1/2 inch (13 mm) thick, or that operate
at peripheral speeds greater than 1800 Surface Feet Per Minute (9 Surface Meters per Second). Serious injury may result from the use
of improper wheels with this grinder.
•
Make certain wheels and other abrasive accessories properly fit the arbor. Do not use reducing bushings to adapt any arbor unless
such bushings are supplied by and recommended by the accessory manufacturer. Improper fit may cause serious injury.
Inspect collet, threads and nut for damage and wear prior to mounting accessory. Thread-on collets shall be securely seated against
•
the driving member. Damaged or improperly installed collets may come loose or may not properly hold accessories. Serious injury
may result.
Do not use a grinding wheel or other bonded accessory that has been exposed to freezing temperatures, extreme temperature
•
changes, high humidity, solvents, water or other liquids. Serious injury may result from the failure of the bond in these accessories.
EN-3
45619418_ed2
Publicidad
Tabla de contenido
