Description Of Symbols; General Safety - Triton TWX7 Instrucciones De Uso

Introduction
Thank you for purchasing this Triton tool. This manual contains information necessary for safe and effective operation
of this product. This product has unique features and, even if you are familiar with similar products, it is necessary to
read this manual carefully to ensure you fully understand the instructions. Ensure all users of the tool read and fully
understand this manual.

Description of Symbols

The rating plate on your tool may show symbols. These represent important information about the product or
instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Class I construction (protective earth)
Conforms to relevant legislation and safety standards.
Risk of electrocution!
Be aware of kickback!
WARNING
LIFTING HAZARD
Single Person Lift could cause injury
Use assistance when moving or lifting
WARNING: This product is heavy and as a precaution it is advised that two people assemble the machine.
Caution!
Toxic fumes or gases!
DO NOT touch! DO NOT access the guard without removing the power. Keep children and bystanders
away while operating a power tool. Distractions can cause you to lose control. All visitors should be kept
safe distance from work area.
Indoors use only!
DO NOT use in rain or damp environments!
Environmental Protection
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for recycling advice.
WARNING: Moving parts can cause crush and cut injuries.
MAX Maximum load
150
kg
GB
3
Original Instructions
Specification
Chassis specification
Model number:
Dimensions (standing):
Dimensions (folded):
Module insert dimensions (LxWxD):
Max load capacity:
Net weight (chassis only):
Electrical switchbox specification
Rating :
Max power rating:
No voltage release (NVR) switch with knee
operation:
Ingress protection:
Length of power cord:
Protection Class:
Clamping Table Module specification
Model number:
Bench dog holes:
Bench dog hole diameter:
Net weight of module:
Note : Imperial measurements are approximate

General Safety

1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are
removed from tool before turning it on.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations, or expose them to rain.
Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.
7. DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not designed.
9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a
drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the
heavier the cord.
10. WEAR PROPER APPAREL Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may
get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only
have impact resistant lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and it frees both
hands to operate tool.
13. DON'T OVERREACH. Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for
lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended accessories. The use of
improper accessories may cause risk of injury to persons.
18. NEVER STAND ON TOOL Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally
contacted.
19. CHECK DAMAGED PARTS. Before further use of the too., a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform its intended function - check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't leave tool until it comes to a complete stop.
Ampere Rating
More Than Not More Than
0
6 10
10 12
12 16
TWX7
40 ¾" x 29" x 35 ½" (1036 x 737 x 900 mm)
39 ¼" x 29" x 12 ½" (995 x 737 x 317 mm)
26" x 16 ⁄ " x 2" (660 x 410 x 50mm)
1
4
330 lbs (150 kg)
51 lbs (23.2 kg)
120V~ 60Hz
15A
Mounted at the front of the chassis
IP52
1.2m (4ft approx)
Class I
TWX7CT001
40
Ø 20 mm (for ¾" dogs)
8.4lbs (3.8 kg)
Table A
Volts Total length of cord in feet
120 25
240 50 100
Minimum gage for cord
6 18
18
16
14
50 100 150
200 300
16 16 14
16 14 12
16 14 12
12 Not Recommended