Publicidad
KEEP MACHINE CLEAN
Periodically blow out all air passages with dry compressed
air. All plastic parts should be cleaned with a soft damp
cloth. NEVER use solvents to clean plastic parts. They could
possibly dissolve or otherwise damage the material.
Wear ANSI Z87.1 safety glasses while
using compressed air.
FAILURE TO START
Should your machine fail to start, check to make sure the
prongs on the cord plug are making good contact in the
outlet. Also, check for blown fuses or open circuit breakers
in the line.
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE! SAW WILL NOT START
WHAT'S WRONG?
1.Saw not plugged in.
2.Fuse blown or circuit breaker tripped. 2.Replace fuse or reset circuit breaker.
3.Cord damaged.
4.Brushes worn out.
TROUBLE! SAW MAKES UNSATISFACTORY CUTS
WHAT'S WRONG?
1.Dull blade.
2.Blade mounted backwards.
3.Gum or pitch on blade.
4.Incorrect blade for work being done.
TROUBLE! BLADE DOES NOT COME UP TO SPEED
WHAT'S WRONG?
1.Extension cord too light or too long.
2.Low house current.
TROUBLE! MACHINE VIBRATES EXCESSIVELY
WHAT'S WRONG?
1.Stand or bench on uneven floor.
2.Damaged saw blade.
Service Information
Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers
are staffed with trained personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986.
Accessories
Recommended accessories for use with your saw are available from your local dealer or authorized service center. If you need
assistance regarding accessories, please call: 1-800-544-6986.
The use of any non-recommended accessory such as dado sets, molding cutters or abrasive wheels may be hazardous.
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or
repaired at no charge in either of two ways:
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating
retailer). Returns should be made within the time period of the retailer's policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase
may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our
option. Proof of purchase may be required. Black & Decker owned and authorized service centers are listed under "Tools-Electric" in the yellow pages of
the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state.
Should you have any questions, contact the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.
MAINTENANCE
TROUBLESHOOTING
WHAT TO DO...
1.Plug in saw.
3.Have cord replaced by authorized service center.
4.Have brushes replaced by authorized service center.
WHAT TO DO...
1.Replace blade.
2.Turn blade around.
3.Remove blade and clean with turpentine.
4.Change the blade.
WHAT TO DO...
1.Replace with adequate size cord.
2.Contact your electric company.
WHAT TO DO...
1.Reposition on flat level surface.
2.Replace blade.
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
LUBRICATION
Apply household floor paste wax to the
extension table or other work surface weekly.
PROTECTING CAST IRON FROM RUST
To clean and protect cast iron tables from rust, you will
need the following materials: 1 pushblock from a jointer,
1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1
can of WD-40
®
, 1 can of degreaser, 1 can of TopCote
Aerosol. Apply the WD-40 and polish the table surface
with the Scotch-Brite pad using the pushblock as a
holddown. Degrease the table, then apply the TopCote
accordingly.
See 'Tools-Electric'
– Yellow Pages –
for Service & Sales
25
machine
table and
®
®
Publicidad
