Publicidad
12 | English
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Warnings for Sander
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Only use the power tool for dry sanding. Water entering
u
a power tool will increase the risk of electric shock.
Warning: Danger of fire! Avoid overheating the work-
u
piece and the sander. Always empty the dust collector
before taking a break from work. Sanding dust in the
dust bag, microfilter, paper bag (or in the filter bag or va-
cuum cleaner filter) can spontaneously combust under
certain conditions, for example if flying sparks are cre-
ated when sanding metals. This risk is increased if the
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry sanding of wood, plastic,
metal, filler and varnished surfaces.
1 609 92A 4AE | (14.06.2018)
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Orbital stroke rate preselection thumbwheel
(2) On/off switch
(3) Lock-on button for on/off switch
(4) Complete dust box (Microfilter system)
(5) Clamp
(6) Sanding plate
(7) Sanding sheet
(8) Release button for front clamping bracket
(9) Front clamping bracket
A)
(10) Punch
(11) Screws for sanding plate
(12) Extraction outlet
(13) Filter element (Microfilter system)
A)
(14) Dust extraction hose
(15) Handle (insulated gripping surface)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Orbital sanders
Article number
Rated power input
Orbital stroke rate preselec-
tion
No-load speed
No-load orbital stroke rate
Orbit diameter
Sanding sheet dimensions
– Hook-and-loop backing
– Clamping tension
Sanding plate dimensions
Weight according to
EPTA Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/vibration information
Noise emission values determined according to
EN 62841-2-4.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 80 dB(A); sound power level
91 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
GSS 23 AE
3 601 K70 7..
W
190
●
rpm
7000–12000
rpm
14,000–24,000
mm
2.0
mm
93 x 185
mm
93 x 230
mm
92 x 182
kg
1.7
/ II
Bosch Power Tools
Publicidad
