Chicago Pneumatic CP8528 Serie Manual De Instrucciones página 8

EN
English
1. Technical Data (See figures 1.)
chuck
drilling
capacity
steel
Model
1
[inch.]
[mm]
[mm]
a :Drilling into metal , a :Screw driving without impact, k Uncertainty , L
h,D h
Declaration of noise and vibration statement (EN60745)
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
These declared values were obtained by laboratory type testing in accordance with the stated standards and are suitable for comparison with the declared va-
lues of other tools tested in accordance with the same standards. These declared values are not adequate for use in risk assessments and values measured
in individual work places may be higher. The actual exposure values and risk of harm experienced by an individual user are unique and depend upon the way
the user works, the workpiece and the workstation design, as well upon the exposure time and the physical condition of the user. We, CHICAGO PNEUMATIC
TOOLS , cannot be held liable for the consequences of using the declared values, instead of values reflecting the actual exposure, in an individual risk
assessment in a work place situation over which we have no control. This tool may cause hand-arm vibration syndrome if its use is not adequately managed.
An EU guide to managing hand-arm vibration can be found at www. pneurop.eu/uploads/documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf We
recommend a programme of health surveillance to detect early symptoms which may relate to noise or vibration exposure, so that management procedures
can be modified to help prevent future impairment.
2. Machine type(s)
• This product is designed for installing and removing threaded fasteners in wood, metal and plastic.This product is designed for drilling or reaming holes.No
other use permitted. For professional use only.
• Please read the instructions carefully before starting the machine.
3. Mounting instruction
• See figures
Battery
4.
• New battery packs reach full loading capacity after 4 - 5 charging and discharging. Battery packs which have not been used for some time should be rechar-
ged before use.
• Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
• The contacts of chargers and battery packs must be kept clean.
• For an optimum life-time, the battery packs have to be fully charged, after use.
5. Maintenance instruction
• Follow local country environmental regulations for safe handling and disposal of all components
• Maintenance and repair work must be carried out by qualified personnel using only original spare parts. Contact the manufacturer or your nearest authorised
dealer for advice on technical service or if you require spare parts.
• Always ensure that the machine is disconnected from energy source to avoid accidental operation.
• High wear parts are underlined in the parts list.
• To keep downtime to a minimum, the following service kits are recommended:
Tune-up kit: see part list
6. Disposal
• The disposal of this equipment must follow the legislation of the respective country.
• All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.
• Repair only by technical maintenance staff.
7. SYMBOL
Please read the instructions
carefully before starting the
machine.
Remove the battery pack
before starting any work on
the machine.
8. Declaration of conformity
We : CHICAGO PNEUMATIC Tool Co. LLC 1800 Overview Drive Rock Hill, SC 29730 - USA
Machine type(s): Compact drill
Declare that the product(s): CP8528
Origin of the product: China
is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to "Machinery" 2006/42/EC, RoHs 2011/65/EU,
EMC 2004/108/EC applicable harmonised standard(s) :
EN 60745-1:2009 + A11:2010, EN 60745-2-1:2010, EN 60745-2-2:2010, EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
Name and position of issuer : Nicolas Lebreton ( R&D Manager)
Place & Date: Saint-Herblain, 28/07/2014
Technical file available from EU headquarter. Nicolas Lebreton R&D manager LLC CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Herblain - France
Original Instructions are in English. Other languages are a translation of the original instructions.
Copyright 2014, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers and drawings.
Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability..
working capacity
stall torque
drilling wood screw wood
2 3
[ft.lb]
[mm] [mm]
[Nm]
Do not dispose of electric tools together with
household waste material! In observance of
European Directive on waste electrical and
electronic equipment and its implementation
in accordance with national law, electric tools
that have reached the end of their life must be
collected separately and returned to an environ-
mentally compatible recycling facility.
Serial Number: From 00001 to 99999
Speed
Dimension
Weight
L x W x H
1st Gear 2nd Gear
4 5
[lb] [inch.]
[rpm] [rpm]
[kg] [mm]
Sound pressure dB(A), K
pA pA
CP8528 Series
Sound
Battery Volt-
pressure
age
L
pA
v
6 7 8
[volt] [dB(A)]
= K = 3 dB Uncertainty.
WA
European Conformity Mark
EurAsian Conformity Mark.
•
Compact drill
Vibrations
Sound-
power
a
k
L
h
wA
9 10
[dB(A)] [m/s²] [m/s²]