Publicidad
Idiomas disponibles
Idiomas disponibles
2
Press this button to feed paper.If you press this button for a long time,
the paper will be fed continuously.
Power Indicator
The green light indicates the starting state,and the red light indicates
the charging state.
When the red light goes out,indicating the battery is full.
Bluetooth Indicator
Green light means bluetooth connection;Green light goes out means
bluetooth is disconnected.
Bluetooth Indicator
Power Indicator
Power Button
FEED Button
STATUS Indicator
Red light is always on and buzzes,the printer is in the state of paper
shortage;The red light goes out after the paper is checked.
Buzzer
Out of paper and overheating,the buzzer sounds every 2 seconds.
Bluetooth connection :The buzzer rings once.
Interface
USB can communicate and transmit data;
Rechargeable:recommended charging power 5V/2A (sold without
power adapter).
Cautions:
1.The printer can only work with the dedicated battery & power adapter.
Otherwise, it may cause harm to the printer.
.
2 If the printer will not be used for a long period of time, the battery must be
taken out of the printer. Otherwise, it may cause battery leakage.
.
3 The fluid of battery used in the printer is caustic. If accidentally the battery
leaks and the fluid is put on skin or clothes, please flush with running water
immediately. And if the fluid gets into eyes, please go to hospital immediately.
.
4 The printer must not be put into water or exposed to rain. Otherwise, it may
cause harm to the printer.
5. Although the printer can work in environment temperature between 0
it may affect printing quality if environment temperature is too low or too high.
Print-head cleaning:
Timely clear printer-head in one of the below cases:
1. Unclear printing.
2. Unclear vertical column in printing paper.
3. Loud noise when feeding.
Cleaning steps are as follows:
1. Turn off the printer and open the top cover. Remove the paper if any.
.
2 Temperature of print-head can be very high right after finishing the printing task.
Please clean print-head after it cools down to environment temperature.
3. Clean the thermal elements of thermal head with a soft cotton cloth moistened
with absolute ethyl alcohol.
4. Close the top cover after the absolute ethyl alcohol completely volatilized.
Then printer self-test page.
STATUS Indicator
USB Interface
℃
green indicator flashes and the buzzer rings then release the FEED
button.At this point,the initialization has been completed.Press the
POWER button again to start up and work normally.
1.Please make sure power off when maintaining printer.
2.Don't touch or scratch printing head surface by hands or metal materials.
3.Avoid using gasoline, acetone or other organic solvent.
4.Turn on the printer and continue print task after the absolute ethyl
alcohol completely volatilized.
STATEMENT
.This device complies with Part 15 of the FCC Rules. Operation is subject to the following
℃,
to 40
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
.Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
.NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
25 seconds after the printer's
:
Publicidad
