Reflex Variomat Touch VS 2-1 35 Manual De Instrucciones Original página 32

I/O module (optional expansion module)
Module address
1 2 3
1 1 0 0
2 0 1 0
3 1 1 0
4 0 0 1
5 1 0 1
6 0 1 1
7 1 1 1
8 0 0 0
9 1 0 0
10 0 1 0
Location Signal
Message text
evaluation
INPUTS
1 Normally closed External temperature
contact
2 Normally closed External signal, Minimum
contact
3 Normally closed
contact
4 Normally open
contact
5 Normally open
contact
6 Normally open
contact
OUTPUTS
1 Changeover
contact
Changeover
2
contact
3 Changeover
contact
4 Changeover
contact
5 Changeover
contact
6 Changeover
contact
5.3 Replacing the fuses
DANGER
Risk of electric shock!
Risk of serious injury or death due to electric shock. Some parts of the main
board may still carry 230 V voltage even with the device physically isolated
from the 230 V power supply.
• Before you remove the covers, completely isolate the device controller
from the power supply.
• Verify that the main circuit board is voltage-free.
32 — English
DIP switch Used for the
modules
4 5 6 7 8
0 1 0 0 0
0 1 0 0 0
0 1 0 0 0
0 1 0 0 0
0 1 0 0 0
0 1 0 0 0
0 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
Error memory
entry
Yes
monitoring
Yes
pressure
Manual make-up Yes
Emergency-Off Yes
Manual pump 1 Yes
Manual OF-1 Yes
--- ---
--- ---
--- ---
--- ---
--- ---
Make-up fault ---
Variomat Touch — 09.09.2022-Rev. C
5.2.3 I/O module default settings
The inputs and outputs of the I/O module each have default settings.
1
These default settings can be changed, if required, and adjusted to local
2
conditions.
3
Responses by the inputs 1 – 6 of the I/O module are recorded and displayed in
4
the device controller's fault memory.
5

Note!
6
• Default settings apply to software version V1.10 and higher.
7
• All digital inputs and outputs can be set freely as option. The
8
setting is carried out by Reflex Customer Service,  13.1 "Reflex
Customer Service",  49
9
10
Priority Signal on the input triggers the following action
Yes • Solenoid valves are closed.
•
•
• Output relay (1) is switched.
No • Solenoid valves are closed.
•
•
• Output relay (2) is switched.
Yes • Solenoid valve (1) in make-up line is manually opened.
• Output relay (5) is switched.
Yes • Pumps (1) and (2) are switched off.
• Solenoid valves (2) and (3) in the overflow pipes are closed.
• Solenoid valve (1) in the make-up line is closed.
• Switches "Group fault" in the device controller.
Yes • Pump (1) is manually switched on.
• Output relay (5) is switched.
Yes Solenoid valve (1) is opened.
--- See input 1
--- See input 2
--- • Below minimum pressure.
• "ER 01" message in the controller
--- • Maximum pressure exceeded
• "ER 10" message in the controller
--- Switches in manual mode
Switches in stop mode
Switches with inputs 3,5,6 active
--- • Make-up setting values exceeded.
• Switches the following messages in the device controller:
•
•
•
•
•
Fusing is provided on the I/O module's main circuit board.
Solenoid valve (2) in overflow pipe (1)
Solenoid valve (3) in overflow pipe (2)
Solenoid valve (2) in overflow pipe (1)
Solenoid valve (3) in overflow pipe (2)
"ER 06", Make-up time
"ER 07", Make-up cycles
"ER 11", Make-up quantity
"ER 15", Make-up valve
"ER 20", Maximum make-up quantity