Global 292855 Manual Del Usuario página 3

Existing Frigidaire sleeves may have older single-sided
intake grilles.
These grilles should be replaced with the dual intake
grille type.
• Remove the existing grille and save the mounting screws.
• Place the grille included with your new air conditioner
towards the inside rear of the sleeve.
• Attach the new grille by aligning the four mounting holes.
• Re-insert the self-tapping screws into the nylon retainers.
Grille Removal
Important: Single intake grille must be removed when
used with the dual intake through the wall units.
Warning: When removing grille, protect it from falling
by securing it with a leash. This can be cord fastened or
strapping looped through the grille and secured with a
knot. While holding the grille by the leash with one hand,
the retaining screws can be removed and the grille can
be brought inside through the front of the sleeve.
Direct Unit Mounting
In cases where the dual intake grille cannot be mounted
directly to the sleeve it is recommended to attach the grille
to the back of the wall unit to the predrilled hole in the unit.
1. Attach the 2 seals (1" x 3/8" x 14"), as shown in Fig. 3.
Seal
Fig. 3
2. Position the grille over the rear of the unit making sure that:
a. The double set of screw holes are at the bottom.
b. The intake fins on either side are pointed away
from the unit.
3. Align the top of the grille with the top of the unit. The
overhang on each side is equal.
4. If the unit has not been predrilled (some models),
1 /8
carefully drill 4 " holes through the grille and into the
side flange of the unit approximately 1
top and bottom, as shown in Fig. 4 and 5. Be careful not
to break the copper pipe.
5. Install 4-#8 self-tapping screws to affix the grille to the unit.
6. Insert the unit into the sleeve.
Grille to Sleeve Attachment
In cases where the dual intake grille fits inside the sleeve
and the grille flange overlaps the sleeve flange, direct
attachment may be possible.
IMPORTANT: If the suitable grille is not used, it may lead
to product damage and possible failure.
Through The Wall
Air Conditioner
Seal Installation
1. 1" x 3/8" x 25" long seal in the center at the top of the
2. 1" x 3/8" x 14" seals to the left and right sides of the sleeve.
3. Cut 1"x 3/8" x 25" long seals to 14" long each and attach
4. Place one 1/2" x 3
Seal
5. Gently slide unit into sleeve.
Ground Wire Installation
1. Install screw end of ground wire into inside of sleeve,
2. Before sliding unit all the way back, remove second
3. Remove plastic washer from screw.
1 /2 " to 2" from the
4. Screw the other end of the ground wire into the unit as
5. Slide unit completely to the rear.
Existing Dual Intake Grille
In cases where the existing sleeve is already installed
with a dual intake grille, the existing. grille may be left
in place. Make sure the outer 3
angled from the left and right sides of the sleeve toward
the center. This provides proper flow of outside air into
the unit. From the installation kit, apply two 1" x 3/4" x
14" seals along the flat metal flange of the condenser.
3
Locations
Fig. 4
Fig. 5 1/8 Hole Grille & Flange
sleeve. Remove the back paper and press into position.
them to the vertical sections of the grille as shown.
1 / 2 " x 1
side wall. Place in center of side wall with the tapered
end facing the opening.
4
Fig. 6
according to preparation instruction.
screw from left side of unit.
shown. Make sure the toothed washer is against the cabinet.
User's Manual
Grille
Screw
#8 Screw
1 / 2 " centering block on each
1
2
4
3
1 /2 " to 4 1 /2 " louvers are