Kärcher NT 50/1 K Manual Del Usuario página 14

Installing the flat fold filter or candle filter
Note
A flat fold filter or candle filter is not included in the
scope of delivery.
1. Open the filter cover.
2. Remove the filter frame.
3. Remove the coarse dirt filter from the filter frame.
4. Flat fold filter only: Insert the flat fold filter (special
accessory) into the filter frame. During insertion, en-
sure that the flat fold filter is flush on all sides. Insert
the filter frame into the suction head.
5. Candle filter only: Insert the candle filter (special ac-
cessory) into the suction head.
6. Close the filter cover until it audibly latches into
place.
Installing the brush strip
1. Remove the squeegee.
Illustration L
2. Install the brush strip.
Installing the fleece filter bag
1. Unlock and remove the suction head.
2. Fit the fleece filter bag (special accessory).
Illustration M
3. Fit and lock the suction head.
Installing the dust bag
Note
The dust bag opening must be pulled fully over the suc-
tion hose port.
1. Unlock and remove the suction head.
2. Attach dust bag (special accessories).
Illustration N
3. Pull the dust bag (special accessories) over the con-
tainer.
4. Fit and lock the suction head.
Clip connection
The suction hose is equipped with the clip 2.0 connec-
tion. All accessory parts with nominal width DN 40 and
a clip 2.0 connection can be connected.
Illustration O
Operation
DANGER
Danger of electric shock
Risk of injury and damage.
The socket is only intended for direct connection of the
disposal pump to the vacuum cleaner. Any other use of
the socket is prohibited.
Switching on the device
1. Plug in the device's mains plug.
2. Switch on the device at the turn switch.
3. Continuously dispose of large fluid amounts: Switch
on the disposal pump.
Adjusting the suction power
Note
With the aid of the suction control, the amount of water
sucked in (pump capacity of the suction turbine) can be
adjusted to the output of the disposal pump. This pre-
vents the suction turbine from constantly switching off
and on and ensures continuous suction.
1. Remove the angle piece from the suction hose.
Illustration P
2. Install the suction control on the suction hose.
14
3. Connect the angle piece to the suction control.
Make sure that the clip ring is aligned as shown in
the illustration.
Illustration Q
4. Regulate the suction power on the suction control
(3-stage).
Disposal and cleaning operation
1. Continuously dispose of liquids or perform cleaning.
Emptying the pre-filter
1. Unlock and remove the suction head.
2. Remove the cable clip of the disposal pump.
3. Pull the pre-filter over the suction hose port and re-
move it.
4. Empty the pre-filter.
5. When inserting the pre-filter, push it over the suction
hose port until it touches the container wall.
6. Insert the cable clip of the disposal pump.
7. Fit and lock the suction head.
Switching off the device
1. If necessary, switch off the disposal pump.
2. Switch off the device at the turn switch.
3. Pull out the device's mains plug.
Each time after use
1. Empty the container.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Folding the push handle in/out
1. Release the push handle lock and adjust the push
handle.
Storing the device
1. Store the suction hose and mains cable as shown in
the illustration.
Illustration R
2. Store the device in a dry room and secure it against
unauthorised use.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
ATTENTION
Improper transportation
Risk of damage
Protect the mains plug of the disposal pump from dam-
age, as it reaches down to the ground when unplugged.
1. Remove the suction hose with floor nozzle from the
support. Carry the device by the carrying handle and
the suction pipe, not by the push handle.
2. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.
English
Transport
Storage