Publicidad
Idiomas disponibles
Idiomas disponibles
English
35. Disconnect the connection cable from the mains and
remove the battery from the tool before carrying out
any conversion, maintenance or cleaning.
36. Where applicable, follow the occupational health and
safety directives or regulations for the prevention of
accidents pertaining to the use of compressors.
37. Observe the legal provisions for the operation of
systems requiring monitoring.
38. Do not modify the tool.
39. Risk of accident. Position the connection cables in
such a way that no one is obstructed.
40. Keep the connection cables away from sharp edges,
do not bent, do not tie together and do not place
anything on them.
41. Do not use adapter plugs or extension cords.
42. When disconnecting the power supply: Do not pull on
the cable. Grab the plug instead.
43. Tool plugs must match the outlet. Never modify the
plug in any way. Unmodified plugs and matching
outlets will reduce risk of electric shock.
44. Have your tool serviced by a qualified repair person
using only genuine replacement parts. This will
ensure that the tool functions safely.
45. Do not use the product if the tool or the battery
terminals (battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
46. Keep the tool's terminals (battery mount) free of swarf
and dust.
○ Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool from
falling on the battery.
○ When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result
in smoke emission or ignition.
47. Hold the handle while carrying the product. (Fig. 16)
48. Always use the tool and battery at temperatures
between 23°F (-5°C) and 104°F (40°C).
49. Definitions for symbols used on this inflator
V.......................................................................... volts
.......................................................... direct current
n
0
......................................................... no load speed
---/min............. revolutions or reciprocation per minute
6
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers. To
avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and operating
instructions for battery charger Model UC18YFSL.
2. Before using battery charger, read all instructions and
cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. To reduce risk of injury, charge metabo HPT
rechargeable battery models of the multi volt series
and the BSL18 series. Other models of batteries may
burst causing personal injury and damage.
4. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
6. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere
rating of battery charger as specified in Table 1.
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating
Amperes *
1
Equal to
or
but less
greater
than
than
0
2
2
3
3
4
AWG Size of Cord
Length of Cord, Feet (Meter)
25
50
100
(7.5)
(15)
(30)
18
18
18
18
18
16
18
18
16
150
(45)
16
14
14
Publicidad
