Bosch GKS Professional 18V-57-2 Manual Original página 20

20 | English
LED
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Fitting
Only use saw blades the maximum permitted speed of
u
which is higher than the no-load speed of the power
tool.
Inserting/changing the circular saw blade
Before carrying out any work on the power tool (e.g.
u
maintenance, tool change etc.), remove the battery
from the power tool. There is risk of injury from uninten-
tionally pressing the on/off switch.
Wear protective gloves when fitting the saw blade.
u
Danger of injury when touching the saw blade.
Do not use abrasive wheels as the application tool un-
u
der any circumstances.
Only use saw blades that match the specifications
u
given in this operating manual and that are tested and
marked in accordance with EN 847-1
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions.
Removing the saw blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
– Press and hold the spindle lock button (4).
Do not press the spindle lock button (4) while the saw
u
spindle is moving. The power tool may become damaged
if this happens.
– Use the hex key (27) to undo the clamping bolt (26) in ro-
tational direction ➊.
– Swing the retracting blade guard (14) back and hold on
to it firmly.
– Remove the clamping flange (25) and the saw blade (24)
from the saw spindle (22).
1 609 92A 9F7 | (29.05.2024)
Fitting the saw blade (see figure A)
Capacity
To change tools, we recommend that you place the power
40–60 %
tool down on the front side of the motor housing.
20–40 %
– Clean the saw blade (24) and all the clamping elements
5–20 %
to be fitted.
0–5 %
– Swing the retracting blade guard (14) back and hold on
to it firmly.
– Place the saw blade (24) on the mounting flange (23).
The cutting direction of the teeth (direction of the arrow
on the saw blade) must match the rotational direction of
the arrow on the retracting blade guard (14).
– Attach the clamping flange (25) and screw in the clamp-
ing bolt (26) in rotational direction ➋. Ensure that the
mounting flange (23) and clamping flange (25) are in-
stalled in the correct position.
– Press and hold the spindle lock button (4).
– Use the hex key (27) to tighten the clamping bolt (26) in
rotational direction ➋. The tightening torque should be
6–9 Nm, which corresponds to hand-tight plus ¼ turn.
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Chip ejector (see figure B)
The chip ejector (18) can turn freely.
An extraction hose with a diameter of 35 mm or a dust/chip
box (28) can be connected to the chip ejector (18).
To ensure optimum extraction, the chip ejector (18) must be
cleaned regularly.
External dust extraction
Connect the dust extraction hose (29) to a dust extractor
(accessory). You will find an overview of how to connect to
various dust extractors at the end of these operating instruc-
tions.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Bosch Power Tools