Publicidad
Idiomas disponibles
Idiomas disponibles
E N G L I S H
Optional accessories
For use in mitre saw mode:
A3
32 Mitre fence (DE3496)
A4
34 Adjustable stand 760 mm (max. height) (DE3474)
35 Support guide rails 1,000 mm (DE3494)
35 Support guide rails 500 mm (DE3491)
36 Inclinable support (DE3495)
37 Swivelling stop (DE3462)
38 Length stop for short workpieces (to be used with guide rails [35])
(DE3460)
39 Support with removable stop (DE3495)
40 Support with stop removed (DE3495)
41 Material clamp (DE3461)
A5
42 Roller support table (DE3497)
For use in saw bench mode:
A6
43 Extension table (DE3472)
A7
44 Single sliding table (DE3471)
Push sticks (DE3454) (not shown)
For use in all modes:
A8
45 Three way dust extraction kit (DE3500)
Cutting capacities
Cutting capacity in mitre saw mode
Cutting angle
Size of material
H mm
B mm
Straight cross-cut
20
180
30
176
40
170
68
140
85
88
15
210
Table turned 45° to
right for mitre cuts
70
Table turned 45° to
left for mitre cuts
68
Sawhead tilted 45°
for bevel cuts
50
140
Cutting capacity in saw bench mode
Cutting depth adjustment
90° vertical cut
0 - 70 mm
45° bevel cut
0 - 32 mm
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
en - 4
Notes
No packaging piece required
68
With 25 mm packaging piece (fig. B1)
22
With 50 mm packaging piece (fig. B1)
Thin boards only (fig. B2)
95
Cross-cut at max. height
93
Cross-cut at max. height
Mains plug replacement (U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
D
WALT authorized repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2), blue is for
Neutral (N) (4) and green/yellow is for Earth (E).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
leads are correctly fixed at the terminal screws.
Never use a light socket. Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
2
conductor size is 1.5 mm
. When using a cable reel, always unwind the
cable completely. Also refer to the table below.
2
Conductor size (mm
)
Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Cable length (m)
7.515 25
30
45
Voltage
Amperes
Cable rating (Amperes)
230
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
7.1 - 12.0
15
15
115-120
12.1 - 20.0
20
20
Assembly and adjustment
Prior to assembly and adjustment always unplug the tool.
The machine is packed in the saw bench mode for compactness and is
fully assembled for mitre saw operation except for the legs, under-table
plastic guard and blade.
Fitting the legs (fig. C)
• Place the machine upside down on the floor.
• Loosen the four wingnuts (3) and insert a leg (4) into each of the clamps.
• Tighten the wingnuts (3) and turn the table over. Make sure it is level;
adjust the leg clamping height if required.
.
60
6
6
6
6
6
6
6
6
6
6
10
15
10
10
15
15
15
15
20
20
20
20
25
-
21
Publicidad
