Radio Functions - AEG AR 4021 BT Instrucciones De Servicio

MASK Setting to mask station during search:
■
DPI: Alternative frequencies with different
Pl code are excluded from the search.
■
ALL:
Alternative frequencies with different
Pl code and no RDS information with high
signal level are excluded from the search.
EON TA The unit can receive RDS EON data. EON means
the transmission of additional programme in-
formation within a station group. In the event
of a traffic announcement (TA), it will switch
within a station group from a non-traffic
broadcast to the corresponding traffic radio
station of the station group.
■ DX
: The unit attempts to receive the EON
TA information from a receivable station
and thus to improve the reception quality.
■
LO : This prevents switching to a programme
with too weak a signal level.
TA VOL Traffic Announcement Volume
REG Some stations split their programme at certain
times into regional programmes with different
content.
■ ON
: Only the regional programmes of the
station are played.
■
OFF : National programmes are also played.
Loudness Function
/BND (26) to activate the Loudness
Press and hold
‹
function. LOUD ON is displayed. The Loudness function
enhances the bass frequencies.
Press and hold /BND (26) again to deactivate the
‹
Loudness function. LOUD OFF is displayed.
Sound Settings
Repeatedly press EQ/TA (19) to cycle through the set-
‹
tings FLAT, CLASSICS, POP M, ROCK M or DSP OFF.
The selected setting is displayed.
Display Information
Repeatedly press DISP (20) to cycle through the following
display information:
Time (is automatically set if RDS reception is enabled),
radio station, programme type, frequency of the currently
set radio station, information on file names (only during
playback of a MP3 or WMA file).
NOTE
►
If there is no corresponding information,
is shown on the display.
►
If the information is too long for the display, it is
displayed as scrolling text.
Setting the time manually (in Radio Mode)
If the time should not be set automatically, proceed as
follows:
Press the button
‹
time appears on the display.
Keep the
‹
flashes on the display.
Use the
‹
Use the
‹
Reset Radio
To reset the unit to default settings press RESET (30) with
a pointed object, i.e. pen.
Reset the unit when:
using it the first time after all cabling is done,
‹
malfunctions of buttons occur,
‹
error messages are displayed.
‹

Radio Functions

Set RADIO Mode
Repeatedly press
‹
band are displayed.
Select Frequency Band
Press
‹
and AM. The selected frequency band is displayed.
Auto Search
Press
‹
displayed. Search stops if a station is found.
Manual Search
Press and hold
‹
displayed.
Press
‹
cy band in steps of 0.05 MHz and 9 kHz for AM until
the desired frequency is displayed.
After two seconds idling the unit returns to auto search.
The display shows AUTO.
Save Station
For each frequency band 6 station presets are available.
Press and hold the desired numeric button (8) approx.
‹
2 seconds to save the current station. A beep can be
heard after successful storage (except setting to BEEP
OFF).
Access Saved Station
PTY NONE
Press
‹
band.
Press one of the numeric buttons (8) to access the
‹
respective station.
Auto Save
Press
‹
band.
ENGLISH
DISP (20) for a short while until the
DISP button (20) pressed until the time
button (23) to set the minutes.
button (23) to set the hours.
PAIR/MOD (4) until frequency and
/BND (26) to toggle between FM1, FM2, FM3
(23) to start auto search, SEARCH is
(23) or
(23) until MANUAL is
(23) or
(23) or (23) to step through the FM frequen-
/BND (26) to select the desired frequency
/BND (26) to select the desired frequency
87