Publicidad
INTRODUCTION
EN
Thank you for the purchase of our quality product. Used carefully and in accordance with the instructions set
out below. Please read and keep these instructions for future reference.
SETUP
1. Place the device on a flat surface, and connect
the plug to an electrical network. Make sure that
the Voltage of the device and the network are
the same.
2. This appliance has two functions: ventilation
and cooler.
3. To start using, open the water tank door and fill it
to the maximum tab line. Close the water tank door
when finished.
4. Press the ON/OFF button to turn it on, it will
make a sound, that means the device is working.
5. The ON/OFF LED indicator light will turn on.
USAGE
1. Press the ON/OFF button to turn on the applian-
ce, it will default to ventilation function.
2. To change the speed press the SPEED button,
it has 3 speeds: low, medium and high. To change
speeds, press the SPEED button until you have the
desired speed.
3. To use the cooling function, press the COOL
button. To turn off this function, press the COOL
button continuously.
Note: only use this mode when the tank has cold
water. Make sure the water in the tank is not lower
than the minimum level while in operation.
4. The device has several modes:
- If you press the MODE button you can choose
between Normal Mode, Natural Mode and Night
Mode.
- With the SWING button you can activate the
fan's oscillation mode, the blades will move from
right to left. To turn it off, press the SWING button
continuously.
- With the TIMER button you can choose the timer.
To increase the time, press the TIMER button
again, it will increase every 30 minutes, up to a
maximum of 15 hours. To turn off this mode, press
the TIMER button continuously.
5. To turn off the device, press and hold the ON/
OFF button continuously.
IMPORTANT: if the cooler will not be used for an
extended period of time, it is recommended that
you empty and allow the unit and filter to dry before
storing. This will prevent mold and unpleasant
odors, and extend the life of the cooler and filter.
18 | www.garsaco.com
MAINTENANCE
We recommend weekly cleaning of your Air
cooler and filter to keeo in best working condi-
tionand replacing the filter every 3-6 months.
Disehwasher: Place filter in tthe top-rack of
you dishwasher & run clycle normally. Remove
and let air dry.
Hand wash: Hand wash gently with warm water
& soap. Shake out exccess water & let air dry.
Microwave: Between washehs, sanitize your
filter by placing in microwave on high for 30
seconds increments, up to 2 minutes. Let sit
until cool.
IMPORTANT: If you see mold on the filter or
notice a mustly, smell, stop and clean the filter
before further use. Fully submerfe the filter
in apot or bowl filled with equal parts clean
water ans white vinegar-allow to soak for 45-60
minutes. Rinse with warm water, wring out and
let air dry.
UNIT CLEANING
To prepare for cleaning, run Air cooler until all
water has emptied from the water tank, or hold
Air cooler over a sink and carefully dump out
to avoid splashing or spilling. Remove filter
tray from Air cooler . Using warm, soapy water,
wipefilter tray and grill, then rinse off until clean.
let air dry.
If you notice water tank is dirty, use a small,
bendable brush(toothbrush, bottle, brush, etc)
and carefull clean the inside of the rank until
clean. Rinse clean with warm water.
FOR BEST RESULTS
1. Pre-soak filter: place your filter under run-
ning cold water until wet.
2. Fill with pitcher: place on flat surface & fill
tank from a water pitcher.
3. Set air flow: point towards you, and adjust
the grill to direct air flow.
4. Filter cleaning: we recommend regular
cleaning of your filter. See product guide or care
& cleaning label on filter dor instructions.
NOTE: you may notice some condensation
forming on yhr front grill. This is normal.
Publicidad
