Publicidad
Enlaces rápidos
M.T.M. s.r.l.
|
BRC Gas Equipment
a Westport Fuel Systems company
Via La Morra, 1
|
12062 Cherasco (Cn)
|
Italy
Tel. +39 0172 48681
|
Fax +39 0172 593113
info@brc.it
|
www.brc.it
Codice istruzione
Instruction code
Code d'instruction
Código instrucción
Versione
Version
Version
Versión
Codice kit
Kit code
Code kit
Código kit
Sistema
Costruttore
Builder
Constructeur
Constructor
Modello
Model
Modèle
Modelo
Cilindrata
Cubic capacity
Cylindrée
Cilindrada
Sigla motore
Engine type
Type de moteur
Código del motor
Petrol ECU
EURO
Cambio
Transmission
Transmission
Transmisión
DA ACQUISTARE SEPARATAMENTE/ TO BUY SEPARATELY
À ACHETER SÈPARÈMENT/ COMPRAR SEPARADAMENTE
KIT UGELLI CNG CON ESTENSIONE TUBO PTFE X COLLETTORI
09SQ99020053
CNG NOZZLES KIT, WITH PTFE EXTENSION PIPE FOR MANIFOLDS
KIT BUSES GNV AVEC RALLONGE TUYAU PTFE POUR COLLECTEURS
(x1)
KIT BOQUILLAS GNC CON ALARGADORA TUBO PTFE PARA COLECTORES
FSM000102R
n° 1 - 09/01/2019
09SM4SDIPD03
SEQUENT DIRECT INJECTION 2.0
Ford
Kuga
1.5 cc - 16 V - 134 kW
M9MA
Continental EMS2510
6B
Automatico
Automatic
Automatique
Automático
Cng
Publicidad
Resumen de contenidos para BRC 09SM4SDIPD03
- Página 1 M.T.M. s.r.l. BRC Gas Equipment a Westport Fuel Systems company Via La Morra, 1 12062 Cherasco (Cn) Italy Tel. +39 0172 48681 Fax +39 0172 593113 info@brc.it www.brc.it Codice istruzione Instruction code FSM000102R Code d’instruction Código instrucción Versione Version n° 1 - 09/01/2019 Version Versión...
- Página 2 Water Agua Depressione riduttore Vacuum reducer Dépression vapo-detendeur Depresión reductor Rail con 4 iniettori Max BRC MY09 E13*67R01*0185* (Rail) Rail with 4 BRC MY09 Max injectors E13*67R01*0262* (Sensor) Rail avec 4 injecteurs Max BRC MY09 E13*67R01*0223* (Injectors) Rail con 4 inyectores Max BRC MY09...
- Página 3 Veuillez respecter les instructions suivantes pendant l’installation du système gaz: • Merci de vérifier sur notre site internet WWW.BRC.IT (“Espace Réservé”) la version et la date de cet instruction! • C’est la responsabilité du mécanicien de vérifier et respecter les normes nationales pour réaliser toutes modifica- tions nécessaires pour le montage.
- Página 4 Ford_Kuga 2X M8X14 CH13 25 mm 25 mm 25 mm 25 mm INCLINAZIONE UGELLI GAS 10° -10° Cyl. 1 Cyl. 2 Cyl. 3 Cyl. 4 Cyl. 1 Cyl. 2 Cyl. 3 Cyl. 4 ø 9 mm M10x1 1±1,5 Nm M.T.M. Srl FSM000102R...
- Página 5 Ford_Kuga 60 mm L60 mm Cyl. 2 Cyl. 3 Cyl. 4 Cyl. 1 M.T.M. Srl FSM000102R...
- Página 6 Ford_Kuga ø 5 mm M6x1 1±1,5 Nm 10±1 Nm 3 Nm M.T.M. Srl FSM000102R...
- Página 7 - Eseguire i collegamenti con saldature a stagno opportunamente isolate - Posizionare i dispositivi elettrici BRC in zona ben ventilata, al riparo da infiltrazioni d'acqua e da fonti di calore - Si raccomanda di isolare i fili della centralina BRC che non vengono collegati - BRC si riserva di modificare il presente schema senza alcun preavviso - Si consiglia di verificare di essere in possesso dell'ultima revisione di schema redatta dalla BRC.
- Página 8 Be careful with the cars for which the manufacturer prohibits or advises against disconnecting the battery, not to alter the antitheft devices or automatic adaptivity - Never use welders connected to the battery of the same car - Connect with suitably insulated soft solderings - Position the BRC electrical devices in a well ventilated area, protected from water seepages and heat sources - We recommend to insulate the BRC electronic control unit wires which are not connected - BRC reserves the right to modify this diagram without notice - We also recommend you to be sure to have the last revision of the diagram drawn up by BRC.