Publicidad
ORIGINAL INSTRUCTIONS
EN
Safety, performance, and dependability have been given
top priority in the design of your multi-tool.
INTENDED USE
The multi-tool is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual and can be considered responsible for their
actions.
The multi-tool is intended to be used:
–
for sanding and finishing metal, wood, plastics, or
similar materials using the sanding pad with the
shaped abrasive sheets provided
–
for scraping and plunge-cutting into non-ferrous
metal, wood, plastics, plasterboard, etc. using the
provided metallic cutting blades
–
for cutting holes in walls to accommodate switches
or power sockets
–
for removing grouting from between ceramic tiles
The multi-tool is intended to be operated indoors in dry,
well-illuminated and adequately ventilated conditions.
The multi-tool is not intended to be used on wet materials
or surfaces.
Do not use the product in any way other than those
stated for intended use.
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
MULTI-TOOL SAFETY WARNINGS
■
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
■
Always wear safety goggles and a dust mask when
sanding, especially sanding overhead.
■
A suitable breathing respirator must be worn while
sanding lead paint, some woods, and metal to avoid
breathing the harmful/toxic dust or air.
■
The dust produced when using the product may be
harmful to the health of the operator and bystanders.
Operator and bystanders shall not touch and not
inhale the dust. Wear a suitable dust protection mask.
■
Do not machine any materials that present a danger
to health, such as asbestos.
■
Clamp the workpiece with a clamping device.
Unclamped workpieces can cause severe injury and
damage.
■
Switch the product off immediately if the accessory
stalls. Do not switch the product on again while the
accessory is stalled, as doing so could trigger a
sudden recoil with a high reactive force. Determine
why the accessory stalled and rectify this, paying
heed to the safety instructions.
■
Ambient temperature range for tool during operation
is between 0 °C and 40 °C.
■
Ambient temperature range for tool storage is
between 0 °C and 40 °C.
■
The recommended ambient temperature range for the
charging system during charging is between 10 °C and
38 °C.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack, or charger in fluid or allow fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between 0 °C and 40 °C.
■
Ambient temperature range for battery storage is
between 0 °C and 20 °C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and
national provisions and regulations.
Follow all special requirements on packaging and
labelling when transporting batteries by a third party.
Ensure that no batteries can come in contact with other
batteries or conductive materials while in transport by
protecting exposed connectors with insulating, non-
conductive caps or tape. Do not transport batteries
that are cracked or leaking. Check with the forwarding
company for further advice.
KNOW YOUR PRODUCT
See page 49.
1. LED light
2. Locking pin
3. Blade release lever
4. Speed control
5. Lock-on button
6. On/Off switch
7. Handle, insulated grasping surface
8. Battery port
9. Wood blade
10. Segment saw blade
11. Operator's manual
12. Sandpaper
13. Sanding pad
14. Battery pack
15. Charger
MAINTENANCE
■
The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when the
product is not in use. Disconnecting the product from
the power supply will prevent accidental starting that
could cause serious injury.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
3
Publicidad
