Silverline 254301 Manual De Instrucciones página 11

4. Check correct function of Karabiner (11) and Scaffold Hook (15), and smooth operation of their
safety mechanisms.
5. Check the Lanyard (14), Rope Thimble (12) and the Protective Sleeves (13) for damage.
Note: Refer to the 'Maintenance' section for further advice on fault conditions.
• If the risk assessment shows that loading over an edge is possible, take appropriate precautions
to ensure safe use of the Lanyard.
Harness fitting & adjustment
• Preparation (see Image A):
1. Identify all parts and straps (see 'Product Familiarisation')
2. Open and release the Chest Buckle (4) and both Leg Strap Buckles (8)
Note: Loosen all three-bar slide and square link type connections fully, in order to retighten during
fitting.
3. Lift the harness on the D-ring of the Dorsal Attachment Point (A) (9), and ensure all straps are
hanging straight
• Fitting shoulder and chest (see Image B-C):
1. Fit the Shoulder Straps (1) of the harness over your shoulders
2. Place your arms through the Shoulder Straps, so the Dorsal Attachment Point (A) (9) is located on
the back
Note: Ensure the harness is not twisted 'inside out' , by checking that the D-ring of the Dorsal
Attachment Point (A) is located outermost.
3. Fasten the Chest Buckle (4), by inserting the three-bar slide through the square link, so both
parts sit flat on top of each other and interlock
4. Adjust the Chest Strap Sliders (3) up or down the harness
Note: The Chest Strap must run squarely over the sternum. It must not run diagonally or close to
the throat region.
• Fitting legs (see Image D-E):
1. Stand upright and straight, locate the Leg Straps (7) and ensure they are not twisted.
2. Reach behind and pass the first Leg Strap in between your legs from back to front.
3. Fasten the Leg Strap Buckle (8), by inserting the three-bar slide through the square link, so both
parts sit flat on top of each other and interlock
4. Repeat on the other side.
5. Adjust the Leg Straps by pulling the end of the webbing through the belt slider, until a snug fit is
achieved and the webbing material sits comfortably, as high as possible, between the inside leg
and groin. Release and readjust if necessary, until a safe fit has been achieved.
WARNING: Correct fitting of the Leg Straps (7) is of paramount concern for the safe and effective
function of the harness. Severe injury can occur during an arrested fall, if the webbing material is
twisted, or if the Leg Straps are not adjusted properly in the groin region.
• Fitting waist belt (see Image F-G):
1. Stand upright and straight, locate both ends of the Waist Belt Strap (5) and ensure they are not
twisted
2. Fasten the Waist Belt Buckle (6), by inserting the three-bar slide through the square link, so both
parts sit flat on top of each other and interlock
3. Adjust the Waist Belt Strap by pulling the end of the webbing through the belt slider, until a
snug fit is achieved
Note: Confirm comfortable yet snug fit of the harness by squatting down and moving your arms
above your head. The user must be able to comfortably move around and reach his working
position, without the harness restricting movement.
Connecting to height safety system components
WARNING: Karabiners and other connectors must ALWAYS be used with the gate closed and
securely locked. Refer to the connector manufacturer's instructions for verification and inspection
procedure.
WARNING: The total length of a lanyard connected to an energy absorber (including
terminations such as rope eyes and connectors such as karabiners and scaffold hooks) must NOT
exceed 2m.
• Use the Dorsal Attachment Point (A) (9) to connect to a shock absorber or shock absorber/lanyard
combination using a suitable karabiner
• DO NOT use the Lateral Attachment Points (10) for connection in a fall arrest system. These
attachment points are for restraint positioning ONLY.
Clearance
Fall clearance (Fig. II):
Before use, it is essential to verify the clearance required beneath the user. This clearance must be
sufficient to prevent the user from hitting the ground or another obstacle, in the event of a fall.
• The necessary clearance should be calculated using the following basic formula:
Connector length including energy absorber elongation + height of the person
+ safety distance = clearance required
• In a fall factor 2 situation with a 100kg load, the safety distance is considered to be 1m. The safety
distance should be calculated appropriately for the fall factor and load of the activity.
Swing falls (Fig. III):
WARNING: The force of striking an object in a swing fall may cause serious injury or death.
• Swing falls occur when the anchorage is not located directly above the point where a fall occurs
• Minimise swing falls by working as close as possible to the anchorage
• DO NOT enter a situation where a swing fall could occur, if it is likely to result in an injury
Note: The risk of swing falls significantly increases the clearance required when using a self-
retracting lifeline or another variable length connecting system.
Connecting to work positioning or restraint systems
Note: This harness is fitted with a Waist Belt Strap (5) and Lateral Attachment Points (10) that enable
its use in work positioning systems. A back up fall arrest system MUST be used if working at height.
• The Lateral Attachment Points are designed to either hold the user in a certain position whilst
working (work in suspension), or to prevent the worker from entering a zone where a fall is
possible (travel restraint, leash principle, see Fig. IV).
• The Lateral Attachment Points must ONLY be used to attach to a work positioning system. DO NOT
connect to a fall arrest system.
• ALWAYS use the two lateral D-rings together by clipping a suitable positioning lanyard between
them. DO NOT connect the lateral D-rings individually.
• There should be a supporting surface for the feet for comfortable work positioning.
• Movement must be restricted to a maximum of 0.6m, and the Lanyard (14) must be kept under
constant tension (see Fig. V).
Anchorage requirements (Fig. VI)
• The minimum strength of any anchorage must be 10kN, according to EN795
• Check anchorage for signs of deterioration.
• As with all height safety equipment, anchorages must be subjected to regular inspections by a
competent person. Inspect at least once every three months and record findings in a dedicated
service record.
• Check that the connector is the correct size for the anchorage to be used. If the connector is too
small, use an anchor sling to connect to the anchorage.
Anchorage position
WARNING: When using this equipment for work positioning the anchorage must be positioned
at or above waist level.
• When using this equipment for fall arrest, the anchorage should preferably be located above
the user's position
Use as part of a fall arrest system
• Anchorages selected for fall arrest systems should be capable of sustaining a static load, applied
in the directions permitted by the system of at least:
o 22kN for non-certified anchorages
o 2 x the maximum arrest force for certified anchorages
o If more than one system is attached to one anchorage, the required strength should be
multiplied by the number of systems attached#
Removing the harness
1. Ensure you are located in a safe place, away from any fall hazards
2. Open both Leg Strap Buckles (8) by passing the three bar slide through the square link
3. Open the Chest Buckle (4)
4. Remove your arms from the harness
Note: Inspect the harness after use, and follow instructions for cleaning, disinfection, transport and
storage as outlined in 'Maintenance' .
Compatibility
• This harness is compatible with miscellaneous height safety systems and safety gear, including
but not limited to the following Silverline products:
o Shock Absorbing Lanyard
WARNING: Always verify that all components used in combination with each other are
compatible.
• Connecting hardware must be compatible in size, shape, and strength. Non-compatible
connectors may accidentally disengage and lead to serious injury or even death.
• Only use connectors, such as D-rings, snaphooks, karabiners and other equipment with a
minimum rating of 22kN or 140kg max load (whichever is appropriate).
Rescue plan
WARNING: A suitable and sufficient risk assessment must be carried out before commencing
with any kind of work at height, or any work that requires the use of personal protective equipment
(PPE) as a control measure.
• The user must have a rescue plan and the means at hand to implement it
• The plan must take into account the equipment and special training necessary to effectively
silverlinetools.com
Restraint Kit
11