Kyocera SENCO XtremePro Serie Instrucciones De Empleo página 5

_______________________________________________
y
Hold the tool correctly with a firm grasp and be prepared
to counteract and manage normal or sudden movements
such as recoil. Grip should be safe but appropriate to
reduce vibration hazard which can cause serious injury.
y
Maintain a balanced body position and secure footing.
y
Be careful when using pneumatic tools as the tool
becomes cold. This can affect grip and control.
_______________________________________________
y
Do not drive fasteners close to the edge of the work
surface.
y
The fastener could deflect and cause injury.
y
Keep bystanders away.
y
Clearly mark off your operting area.
_______________________________________________
y
Disconnect tool from air before doing tool
maintenance, clearing a jammed fastener,
making adjustments,leaving work area,
moving tool to another location, or handing
the tool to another person.
_______________________________________________
y
Tool may eject a fastener when connected to air supply;
therefore, ① remove all fasteners from tool before at-
taching air hose.
y
Be careful when handling fasteners when loading/unload-
ing. Fasteners have sharp points.
_______________________________________________
y
Never use tool if workpiece contact, trigger or springs
have become inoperable, missing or damaged. Do not
tamper with or remove workpiece contact, trigger, or
springs.
y
Modifications may reduce the effectiveness of safety
measures and increase risk to operator/bystanders.
y
Do not use tool if tool has been damaged.
_______________________________________________
y
Make sure all screws and caps are securely tightened at
all times. Make daily inspections for free movement of
trigger and workpiece contact. Never use the tool if parts
are missing, worn or damaged.
y
Always use second handle (if supplied)
_______________________________________________
y
Use only parts, fasteners, lubricants and accessories
recommended or sold by SENCO. Do not modify tool
without authorization from SENCO.
_______________________________________________
y
Use only clean, dry, regulated compressed air at recom-
mended pressure.
y
Always shut off air supply and disconnect tool when not
in use.
_______________________________________________
y
Tools shall not be connected to pressure which potentially
exceeds maximum operating pressure by 10%.
y
Do not exceed the maximum operating pressure Ps max.
_______________________________________________
y
Tools marked with an inverted triangle may not
be used unless fitted with an effective workpiece
contact.
y
Tools without workpiece contact can be fired unintention-
ally, causing injury.
_______________________________________________
y
Stands for mounting tools to a support shall be designed
and constructed by the stand manufacturer in such a way
that the tool can be safely affixed for the intended use.
_______________________________________________
y
The tool and air supply hose must have a connecting
nipple such that all pressure is removed
from the tool when the coupling joint is
disconnected.
y
Compressed air can cause severe injury.
y
Always disconnect the tool from the com-
pressed air supply before changing accessories, making
adjustments and/or repairs or when moving away from
an operating area to a different area.
y
Never direct compressed air at yourself or anyone else
y
Whipping hose can cause severe injury – always check
for damaged or loose hose.
_______________________________________________
y
Do not load fasteners with trigger or workpiece contact
depressed.
_______________________________________________
y
Do not use tool without danger label on tool. If
label is missing, damaged or unreadable, contact
your SENCO representative to obtain a new label.
_______________________________________________
y
Never use a tool that leaks air or needs repair.
y
Do not use if the tool is damaged.
y
Never carry or drag a pneumatic tool by its hose.
_______________________________________________
y
Do not perform any "emergency repairs"
without proper tools and equipment.
y
Always check tool before use for broken,
misconnected, loose or worn parts.
Written approval of the tool manufacturer must be
obtained prior to making any modifications to tool.
_______________________________________________
y
Keep hands and other body parts away
from the area shown in the circle to
avoid possible injury during operation.
y
Keep fingers away from trigger when
not operating the tool and when
moving from one operating position
to another.
5
EN