Publicidad
Idiomas disponibles
Idiomas disponibles
Rip Guide
Angle Guide
Handle
Bottom
Cord Storage
On/Off
Switch/Key
FIGURE 3
PRODUCT SPECIFICATIONS
Input: 4.4 Amps
No-load Speed: 3600 RPM
Output: 2⁄3-Peak HP
Blade Diameter: 7 in. (180 mm)
Rating: 120 Volts~60 Hz AC
Depth of Cut: 1 1⁄8 in. (29 mm)
ASSEMBLY
FOLLOW ALL
OF THE ASSEMBLY AND OPERATION
INSTRUCTIONS COMPLETELY BEFORE
CONNECTING THE SAW TO A POWER
SOURCE OR TURNING THE MOTOR ON.
UNPACKING
1. Remove all packing materials from around
your saw.
2. Carefully lift the saw from carton and
place it on a level work surface.
3. Do not discard the packing materials until
you have carefully inspected the saw for
loose or damaged parts.
The following items are included in box with
your tile saw: 7 in Diamond Blade, Blade
Guard, Rip Guide, Angle Guide, Universal
Wrench and Owner's Manual.
4. Inspect the saw carefully to make sure
that no breakage or damage has occurred
during shipping. If any parts are damaged
or missing, return the saw to your place of
purchase.
IF ANY PARTS ARE
DAMAGED OR MISSING, DO NOT ATTEMPT
TO OPERATE THIS SAW. OPERATING THIS
SAW WITH DAMAGED OR MISSING PARTS
COULD RESULT IN POSSIBLE SERIOUS
PERSONAL INJURY.
INSTALLING THE BLADE
1. Remove right cutting table.
2. Remove baffle (see FIGURE 4)
Blade Guard
Water Reservoir
FIGURE 4
3. Remove blade shaft nut and outer flange.
4. Carefully place the blade onto the shaft
and push it against the inner flange.
5. Be sure the side of the blade with the
directional arrow is facing towards you.
6. Place the outer flange and the blade shaft
nut onto blade.
7. Hold blade and firmly tighten the blade
shaft nut with the included wrench, but do
not over tighten (see FIGURE 5).
FIGURE 5
8. Replace baffle and right cutting table.
CONTINUOUS RIM BLADES WITH THIS
SAW. DO NOT USE SEGMENTED, "TURBO"
BLADES, WOOD SAWING BLADES, BLADES
WITH OPENINGS, OR ANY OTHER CUTTING
DEVICES WITH THIS TILE SAW. USING
THESE BLADES COULD RESULT IN SERIOUS
PERSONAL INJURY AND DAMAGE TO THE
SAW.
INSTALLING THE BLADE
GUARD
1. Loosen the 2 screws on top of the table,
behind the blade slot.
Cutting Table
USE ONLY
– 3 –
2. Insert blade guard support to align with
the screws. Adjust the blade guard support
so that the support aligns with the blade.
3. Tighten screws (see FIGURE 6).
FIGURE 6
4. Remove knob and bolt from the blade
guard.
5. Slip the back end of the blade guard down
over the blade guard support (see FIGURE 7).
6. Replace the knob into the blade guard,
while being careful to hold bolt on the right
side in place, then tighten (see FIGURE 7).
FIGURE 7
7. It is suggested that the front of the blade
guard be pointed slightly down to minimize
the front splash during cutting.
INSTALLING THE RIP GUIDE
(see FIGURE 8)
1. Slide the rip guide on to the saw from
either the right side or left side of the
cutting table.
2. Push down front lever to tighten once it is
positioned for your cut.
FIGURE 8
INSTALLING THE ANGLE GUIDE
(see FIGURE 9)
1. The angle guide is designed to fit on top of
the rip guide. Simply place angle guide onto
the top of the rip guide.
NOTE: The angle guide can be placed on
either the left or right side.
Publicidad
