Descargar Imprimir esta página

GYS 037236 Manual Del Usuario página 5

Ocultar thumbs Ver también para 037236:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 11
UK
8. Le soudage-découpage oxyacétylène, au laser ou au gaz n'est pas autorisé avec ce masque.
The welding helmet GYSMATIC LCD 5/13 XXL complies with EEC directives 89/686 CEE. This conformity is established in compliance with EN 175, EN 166, EN 168 and EN 379.
Notified bodies / organisations :
Cell :
Identification number : 1883
This manual has been made to help you utilise the helmet GYSMATIC LCD 5/13 XXL, supplied ready to use. For your protection, please read these instructions carefully and
consult with a qualified instructor prior to operation.
BEFORE WELDING
-Check that the welding helmet is in good condition and adjust the headband.
-Check whether the front cover lens, the front frame and filter are inserted and fixed in place. In case of problems, please recondition.
-Make sure that the 4 sensors (9) and the cell (8) are not obstructed by dust or debris.
-Make sure that the protection films on both screens are removed.
-Make sure that the red light (4) is off, otherwise change the batterie (11).
-Check that the protection level matches your welding processes. Please refer to the following chart to help your choice (cf. welding process board)
OPERATION
The opto-electronic GYSMATIC LCD 5/13 XXL welding helmet instantaneously switches from light to dark state when a welding arc is struck and switches back to the light
state when the arc stops.
7
1
5
2
3
4
• Button « Shade » : The shade range can be set manually between Din 5 to 13.
1
• Button « Sensitivity » : Sensitivity settings :
2
- Welding process : Level 5 for low intensity TIG welding / Level 3 for most welding processes.
• Button « Delay » : Return time to the light state.
3
Delay is designed for slower switching time to clear state and to eliminate remaining bright rays.
• Button « WELD / GRIND » :
This switch enables you to choose the setting range on either 5-9 or 9-13.
For non-welding operation such as grinding, you can switch off the sensor by selecting «Grind» mode. The LED blinks to indicate that the sensor
4
is off.
WARNING : Make sure to switch back to WELD mode (5-9 ou 9-13) before any welding operation.
• LCD with battery indicator :
5
Switching modes or settings is done by briefly pressing one of these buttons.
• Buttons « MEMORY » :
Can save up to 3 programmes. Hold one of the buttons down(>3 seconds) to save the programme.
6
PRECAUTIONS
• The welding helmet is suitable for use with virtually all welding processes except Oxy-Acetylene welding, laser welding and gas.
• Standard protective screens must be installed on both inside and outside surfaces of the module. Failure to use protective screens may constitute a safety hazard or result
in irreparable damage to the module.
Welding hood / Protection
screen :
10
9
6
8
Clear shade
4
Dark shade
5-13
Filter dimension
114x133x10mm
Reaction speed
0.08 ms
Power supply
Solar + battery
Weight
460 gr
Field of vision
100x83mm
Applications
MMA 5>400A / TIG 5>250A / MIG-MAG 5>500A / Grind
Warranty
1 year
Application temperature
-10°C / + 55°C
Storage temperature
-20°C / + 70°C
Identification number : 0196
1. Button «SHADE»
2. Button «SENSITIVITY»
3. Button «DELAY»
4. Button «WELD / GRIND» + indicator
5. Screen
6. Button «MEMORY»
7. Protection screen
8. Solar cell
9. Sensors
10. Filter
11. Lithium battery 3V CR2450
11
5

Publicidad

loading

Este manual también es adecuado para:

Gysmatic xxl 5-13gGysmatic 5.13 xxl