Bosch AdvancedDrill 18V-80 Manual Original página 21

Setting the operating mode
AdvancedDrill 18V-80:
Screwdriving
1 20
For driving in small and medium-sized screws,
set the torque presetting ring (4) to the re-
quired torque.
Screwdriving and Drilling
For driving in large screws and for drilling, set
the torque presetting ring (4) to the "MAX
drilling/screwdriving" symbol.
AdvancedImpact 18V-80:
Screwdriving
For driving in small and medium-sized screws,
set the operating mode presetting ring (5) to
the "screwdriving" symbol.
Set the torque presetting ring (4) to the re-
quired torque. For maximum torque, set the
1 20
operating mode presetting ring (5) to the "MAX
drilling/screwdriving" symbol.
Screwdriving and Drilling
For driving in large screws and for drilling, set
the operating mode presetting ring (5) to the
"MAX drilling/screwdriving" symbol.
Impact drilling
For impact drilling in masonry, set the operat-
ing mode presetting ring (5) to the "impact
drilling" symbol.
Switching on/off
To start the power tool, press and hold the on/off switch
(13).
The worklight (11) lights up when the on/off switch (13) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
To switch off the power tool, release the on/off switch (13).
Adjusting the speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (13) to varying extents.
A light pressure on the on/off switch (13) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Fully automatic spindle lock (Auto-Lock)
The drill spindle, and therefore the tool holder (3), are
locked when the on/off switch (13) is not pressed.
This enables screws to be screwed in even when the battery
(9) is empty and allows the power tool to be used as a
screwdriver.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
The middle LED of the battery charge indicator flashes.
Bosch Power Tools
Practical advice
Only apply the power tool to the screw when the tool
u
is switched off. Rotating application tools can slip off.
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed for ap-
proximately three minutes without load to cool it down.
Maintenance and Service
Maintenance and Cleaning
Before carrying out any work on the power tool (e.g.
u
maintenance, tool change etc.), remove the battery
from the power tool. There is risk of injury from uninten-
tionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When the batteries are shipped by third parties (e.g. air
transport or forwarding agency), special requirements on
packaging and labelling (e.g. ADR regulations) must be met.
A dangerous goods expert must be consulted when prepar-
ing the items for shipping.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
English | 21
1 609 92A 9H7 | (19.02.2024)