Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Planing
Hold the tool with the nose piece of the shoe resting on
u
top of the workpiece surface.
Switch the tool on.
u
Move the tool steadily forward to perform the cutting
u
stroke.
Switch the tool off after the stroke has been completed.
u
Chamfering Edges (Fig. I)
The V-groove in the front shoe enables location to corner of
material to chamfer at 45degree angles.
Hold the tool at an angle with the corner of the material
u
located in the groove and perform a cutting stroke.
Replacing the drive belt (Fig. G)
Warning! Before replacing, ensure unit is switched off and
unplugged.
Loosen the screws (14) and remove the cover (13).
u
Remove the old drive belt.
u
Place the new belt (16)over the large pulley (15), then
u
over to side of smaller pulley (17) and whilst manually
rotating the large pulley push the Belt up and over the
edge of the small pulley. Keep rotating and pushing the
Belt over the grooves on the small pulley until grooves on
Belt are located correctly into the grooves on the small
pulley.
Put the cover back in place and tighten the screws.
u
Parking rest (Fig. H)
Your planer is equipped with a parking rest (7) that
automatically lowers into place when the tool is lifted from the
work surface. When planing, the parking foot raises as the tool
is pushed forward. When the parking foot is lowered, the
planer can sit on the work surface without the blade contacting
the workpiece.
Hints for optimum use
Move the tool along the grain of the wood.
u
If the grain is cross or curly, or if the workpiece material is
u
a hard type of wood, adjust the depth of cut to take only a
very thin shaving at each pass and take several passes to
achieve the desired result.
To keep the tool in a straight line, press down the front of
u
the tool at the start, and press down the back of the tool at
the end of the cutting stroke.
Accessories
The performance of your tool depends on the accessory used.
Stanley BLACK+DECKER accessories are engineered to high
quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
8
(Original instructions)
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Input voltage
V
AC
Power input
W
No-load speed
min
-1
Planing width
mm
Planing depth
mm
Rebating depth
mm
Weight
kg
Level of sound pressure according to EN62841:
L
(sound pressure) 93 dB(A), Uncertainty (K) 3 dB(A)
pA
L
(sound power) 101 dB(A), Uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN62841:
Vibration emission value (a
BEW712
) 6.6 m/s
, uncertainty (K) 1.5 m/s
2
2
h
230
710
16500
82
2
11
2.4
Publicidad
