Shuttle XH610G2 Guía Rápida

快速安裝指南 Kurzanleitung Guide rapide Guía rápida
XH610G2 Quick Guide
クイックガイド Kраткое руководство 快速安裝指南
More information on this product can be found at: https://bit.ly/S-XH610G2
更多本產品資訊，請蒞臨：https://bit.ly/S-XH610G2
Weitere Informationen zu diesem Produkt finden Sie unter: https://bit.ly/S-XH610G2
Pour plus d'informations sur ce produit, visitez: https://bit.ly/S-XH610G2
Product Overview
產品外觀 \ Produktübersicht \ Présentation du produit \ Resumen del producto \ 製品概要 \ Обзор продукта \ 产品外观
1 2 3 4 2 5 6
6. Hard disk drive LED
1. USB 2.0 Ports
7. COM port (optional)
2. USB 3.2 Gen1 Type-A Ports
8. HDMI 2.0 Ports
3. MIC-in
9. DisplayPort
4. Headphones 10. 2.5Giga LAN Port
5. Power switch / Power LED 11. Giga LAN Port
Hardware Installation
硬體安裝 \ Hardware Installation \ Installation du matériel \ Instalación de hardware \ ハードウェアのインストール \ Установка оборудования \硬件安装
A. HDD or SSD Installation
For safety reasons, please ensure
!
that the power cord is disconnected
before opening the case.
1. Turn your XH610G2 upside down,
then unscrew three screws of the
HDD/SSD cover and remove it.
Install the memory module
(thermal pad 50 x 15 x 2.25 mm
for DIMMB2 slot), if required
(refer step C).
SO-DIMM slot (DIMMB2)
c
2. Mount the HDD/SSD into the
bracket with three screws.
a
b
The product's colour and specifications may vary from the actually shipped product.
L
B. CPU and ICE Module Installation
1. Unscrew these two thumbscrews of the chassis cover, slide the
cover backwards and upwards. Then remove the EPE protective
foam from the top of the thermal fins.
e
c
d
2. Unfasten the four ICE module attachment screws and unplug the fan
connector. Remove the ICE module from the chassis and put it aside.
ICE module
a
b
c
FAN1
 Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
This CPU socket is fragile and can easily be damaged. Always
!
use extreme care when installing a CPU and limit the number of
times you remove or change the CPU. Before installing the CPU,
make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage of the CPU.
3. Unlock and raise
the socket lever.
4. Lift the metal load
plate off the CPU
socket.
a
DO NOT touch the socket contacts. To protect the CPU socket,
! !
always use the protective socket covver when the CPU is not
installed.
Puede encontrar más información sobre este producto en: https://bit.ly/S-XH610G2
本製品の詳細な情報については、次のURLより確認頂けます。https://bit.ly/S-XH610G2
Для получения дополнительной информации об этом продукте перейдите по ссылке: https://bit.ly/S-XH610G2
更多本产品信息，请访问：https://bit.ly/S-XH610G2
17
16
7 8 9 10 11
12. Power Jack (DC IN)
13. Clear CMOS & Power Button & +5V
14. PCIe x1 slot
15. PCIe x16 slot
16. Perforation for optional WLAN (optional)
®
17. Kensington Lock hole
3. Tear off the adhesive tape of the HDD cable.
a
Install the HDD or SSD in the chassis using its bracket.
Affix with three screws and connect the HDD or SSD
with an HDD/SSD cable.
c
b
b
4. Replace the HDD/SSD cover and refasten three screws.
5. Please orientate the CPU correctly and align the CPU notches
with the socket alignment keys. Make sure the CPU sits perfectly
horizontal, then push it gently into the socket.
Align the CPU notches with
the socket alignment keys.
Triangle Pin1 Marking on the CPU
a
Please be aware of the CPU orientation, DO NOT force the
!
CPU into the socket to avoid bending of pins on the socket and
damage of CPU!
6. Tear off the protective membrane from the metal load plate. Close
the metal load plate, lower the CPU socket lever and lock in place.
a
Tear off the protective membrane
7. Spread thermal paste evenly
on the CPU surface.
Thermal Paste
application area
a
b
! Please do not apply excess amount of thermal paste.
8. Screw the ICE module to the motherboard. Note to press down
on the opposite diagonal corner while tightening each screw.
9. Connect the fan.
b
d
b
c
e
a
53R-XH6103-2501
C. Memory Module Installation
This motherboard does only support 1.1 V DDR5 SO-DIMM
!
memory modules.
1. Locate the SO-DIMM and paste the thermal pad on the
motherboard, which can effectively reduce its temperature.
SO-DIMM slot
14 15
DIMMA1 (Top)
DIMMB2 (Bottom)
DIMMA1 (Top)
2 1 12 13
D. M.2 Device Installation
1. Locate the M.2 key slots on the motherboard.
2. Install the M.2 device into the M.2 slot and secure with the screw.
 M.2 2280 M key slot
11a. NVMe+SATA
11b. SATA only
a
HDD/SSD cable
a
Slope angle
F. Installation of Expansion Card
1. Unfasten the expansion slot bracket screw.
Remove the back panel bracket and put it aside.
The maximum permitted size for display cards is
!
205 x 120 x 45 mm. The display cards must be
installed on the riser card, not on the motherboard.
c
G. Complete
1. Replace the cover and tighten the thumbscrews,
then connect the power cord.
2. Complete.
f
b
c Please press the "Del" key while booting to enter BIOS.
!
Here, please load the optimised BIOS settings.
Safety Information
Incorrectly replacing the battery may damage this computer.
!
Replace only with the same or equivalent as recommended by Shuttle.
Dispose of used batteries in accordance with the laws of your country.
更換電池方式錯誤可能會損壞本電腦以及引發爆炸、火災或其他危險。
僅能依 Shuttle 的建議,以相同或同等的電池更換。
請根據您所在國家/地區的法律規定處理廢電池。
Das unkorrekte Austauschen der Batterie kann diesen Computer
beschädigen. Ersetzen Sie die Batterie nur durch den gleichen Typ oder
ein gleichwertiges, von Shuttle empfohlenes Modell. Entsorgen Sie
gebrauchte Batterien gemäß den gesetzlichen Vorschriften in Ihrem Land.
Ne pas replacer correctement la pile peut endommager l'ordinateur.
Remplacez-la uniquement par un modèle identique ou un équivalent
comme recommandé par Shuttle. Éliminez les piles usagées
conformément à la législation en vigueur dans votre pays.
La sustitución incorrecta de la batería puede dañar este equipo. Sustituya
la batería únicamente por una igual o equivalente recomendada por Shuttle.
Elimine las pilas usadas de acuerdo con los requisitos legales de su país.
バッテリを間違ってセットすると、このコンピュータが損傷する原因
となります。交換する際は、Shuttle が推奨するバッテリと同じもの
または同等のものだけを使用するようにしてください。使用済みの
バッテリーは、お住みの国の法律に従って処分してください。
Неправильная замена батареи может привести к повреждению
компьютера. Батарея должна соответствовать стандарту производителя
Shuttle или быть идентичной предыдущей. Утилизируйте использованны
е батареи в соответствии с законодательством вашей страны.
更换电池方式错误可能会损坏本电脑。仅能依 Shuttle 的建议,
以相同或同等的电池更换。请根据您所在国家/地区的法律规定处理废电池。
All bundled parts, power cord included, shall not be used without this product.
電源ケーブル等、すべての付属品は本機以外ではご使用になれません。
f
注意: 仅适用于在非热带气候条件下安全使用,
在热带气候条件下使用时, 可能有安全隐患。
注意: 允许产品使用的最高环境温度为 40℃。
FAN1 * The equipment was evaluated for use in a maximum air ambient
temperature of 40 ºC.
產品宣告最大適用環境溫度為 40 ºC。
注意: 仅适用于海拔 2000m 以下安全使用,
在海拔 2000m 以上使用时, 可能有安全隐患。
2000m
2. Align the notch of the memory module with the one of the relevant
memory slot.
DRAM Thermal pad
Double-sided 50 x 15 x 2.25 mm
DIMMA1 slot
!
(Top) only:
Single-sided 50 x 15 x 3 mm
 Thermal pad
Single-sided
(50 x 15 x 3 mm)
50 x 15 x 2.25 mm
or Double-sided
for single-sided DRAM
DIMMB2 (Bottom)
 Thermal pad
(50 x 15 x 2.25 mm)
for double-sided DRAM
3. Gently insert the module into
the slot in a 45-degree angle.
b
E. How to change the battery
1. Use a flat-blade screwdriver to gently pry the metal tab to disengage
the battery from the battery holder.
 M.2 2230 E key slot
b
a
b
Slope angle
2. Install the new
battery, press it
on the battery
holder keeping
c
c
the positive side
facing top.
a
b
H. Installation of VESA Mount
 Follow the steps 1-2 to install the VESA mount.
! Supports 75x75 mm and 100x100 mm VESA standard.
a
c
DC-IN
d
e
安全資訊 \ Sicherheitshinweise \ Informations de sécurité \ Información de seguridad \ 安全に関する情報 \ Информация о безопасности \ 安全信息
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This device meets the requirements for the EU conformity in
accordance to the currently valid EU directives.
Dieses Produkt erfüllt die Anforderungen für die EU-Konformität
entsprechend der aktuell geltenden EU-Richtlinien.
Ce produit répond aux exigences de la conformité UE suivant les
directives européennes actuellement en vigueur.
WARNING
If swallowed, a lithium button battery can cause severe or fatal injuries within 2 hours.
Keep batteries out of reach of children. If you think batteries may have been
swallowed or placed inside any part of the body, seek immediate medical attention.
1. The statement "remove and immediately recycle or dispose
of used batteries according to local regulations and keep away
from children. Do NOT dispose of batteries in household trash
or incinerate."
(a) Remove and immediately recycle or dispose of used batteries
according to local regulations and keep away from children.
Do NOT dispose of batteries in household trash or incinerate.
(b) Even used batteries may cause severe injury or death.
(c) Call a local poison control center for treatment information.
(d) Indicating the compatible battery type CR2032.
(e) Indicating the nominal battery voltage.
(f) Non-rechargeable batteries are not to be recharged.
(g) Do not force discharge, recharge, disassemble, heat above (manufacturer's
specified temperature rating) or incinerate. Doing so may result in injury
due to venting, leakage or explosion resulting in chemical burns.
2. This Product contains a button Battery/coin cell batteries
(a) Ensure the batteries are installed correctly according to polarity (+ and -).
(b) Do not mix old and new batteries, different brands or types of batteries,
such as alkaline, carbon-zinc, or rechargeable batteries.
(c) Remove and immediately recycle or dispose of batteries from equipment
not used for an extended period of time according to local regulations.
(d) Always completely secure the battery compartment. If the battery
compartment does not close securely, stop using the product,
remove the batteries, and keep them away from children.
SO-DIMM slot
Notch
Thermal Pad
Cutout
Single-sided
DIMMB2 slot (Bottom):
 Thermal pad
(50 x 15 x 2.25 mm)
for single-sided DRAM
or double-sided DRAM
Double-sided
4. Carefully push down the
memory module until it
snaps into the locking
mechanism.
a
45-degree
angle
Latch Latch
Metal tab
a
b
2. Install the PCIe x1 / PCIe x16 card into the
PCIe x1 / PCIe x16 slots.
b
a
Supports two single-slot expansion cards
!
PCIe x16 + PCIe x1. Supports one dual-slot
PCIe x16 slot
PCIe x16 card (which occupies both PCIe slots).
M4x10 * 4pcs
1
XH610G2
Front Panel
M3x7 * 4pcs
2
THIS PRODUCT CONTAINS A BUTTON BATTERY
WARNING