Publicidad
• Do not overload the stroller! Any load placed and / or attached to the handle, board, backrest, canopy and /
or sides of the stroller can affect its stability! The stroller and the seat are designed to carry only one child!
• Do not use spare parts and other components not supplied by the manufacturer! The manufacturer accepts
no liability for safety if used spare parts, different from the original ones or approved by the approved type.
• Do not make changes or modifications to the construction! If necessary, contact your supplier or an
authorized service centre for advice and repair.
• The car seat does not replace the baby seat or crib. When the baby does not need sleep, it should be placed
in a suitable baby stroller, seat or crib.
• Do not use the product if you find any missing or damaged parts!
• Do not allow children under 3 years of age to fully assemble the product to avoid access to small and
disassembled parts!
• Do not place additional cords or ties on the product to avoid the risk of suffocation!
• Do not use the stroller on escalator and be careful when getting down or up on the sidewalk.
• Keep the plastic packaging away from children to avoid the risk of suffocation!
• DO NOT store the product in humid places and in direct sunlight!
SEE FIGURE PD:
PD: 1.One hand fold button; 2.Push handle; 3.Seat adjusting button; 4.Seat detaching button; 5.Luggage
basket; 6.Brake pedal; 7.Rear wheels; 8.Rear wheel detaching button; 9.Front wheel detaching button;
10.Front wheels; 11.Direction lock; 12. 5-point safety belt; 13.Safety bumper; 14.Sun shade; 15.Canopy.
1. UNFOLDING OF THE STROLLER FRAME – FIGURES 1-2: Open the frame by releasing the side safety
mechanism (fold/unfold button) as shown in Figures 1-2. Pull handle up until frame reaches end position
(figure 2). You should hear a clicking sound when the frame locks into place.
2.INSTALLING AND REMOVING THE FRONT WHEELS – FIGURE 3: Insert the front wheel into the front frame
opening as shown in Figure 3. Fix until you hear a click. To disassemble the front wheels, press the button on
the console and pull the wheel down (Figure 3).
3.ORIENTATION OF THE FRONT WHEELS – FIGURE 4: Press the front wheel orientation button as shown in the
direction of the arrow (down), the front wheels cannot rotate. Raise the button as shown in the direction of
the arrow, the front wheels can be rotated (Figure 4).
4.INSTALLING AND REMOVING THE REAR WHEELS – FIGURES 5-6: Insert the rear wheel into the rear frame
opening, as shown in Figure 5. Fix until you hear a click. To remove the rear wheels, push the button and the
wheels are released quickly by pulling out (Figure 6).
5.USING THE BRAKE – FIGURES 7-8: To activate the parking device and lock the two rear wheels, press down
the pedal on the rear axle (Figure 7). To release the brake, pull up the pedal using your foot (Figure 8).
6.INSTALLING SEAT - FIGURES 9-13: Unfold the seat as shown in Figure 9 and place it on a flat surface (Figure
10). Pull the safety board toward you as shown in Figure 11 until it locks (you should hear a clicking sound).
Stretch out the canopy and the sunshade as shown in figure 12. Place the provided mattress - the seat is ready
to use as a winter carry cot.
7.PLACING THE FOOTREST – FIGURES 14-17: Buckle up the first buckle under the front part of the seat, then
fasten the second buckle under the front part of the seat t o set the foot rest part when using the summer
mode of the seat.
8.ADJUSTING SEAT TILT - FIGURES 18-21: Press the strap system button on the back of the seat and move it up
to adjust the seat to the seated position. Press the strap system button and move it down to adjust the seat to
the horizontal position. To increase the stability of the seat base, fasten the textile part with tic-tac buttons to
the metal bar under the seat.
9.OPERATION WITH THE CANOPY - FIGURES 22-23: Pull the canopy forwards, in order to unfold it and
backwards – in order to fold it (Figures 22-23).
10.ATTACH AND DETACH THE SAFETY BOARD – FIGURES 24-26: Insert both ends of the safety board into the
two side holes of the frame (Figure 244). Secure the guard until you hear a click (Figure 25). To remove the
guard, press the release button on both sides of the frame and pull at the same time (Figure 26).
PARTS
ASSEMBLY STEPS AND USE
17
Publicidad
