Important Remarks; Important Safety Instructions; Installation Instructions - Cardin Elettronica BL Serie Manual Del Usuario

IMPORTANT REMARKS

TO REDUCE THE RISK OF SEVERE INJURY OR DEATH READ THE FOLLOWING REMARKS
CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION. PAY PARTICULAR ATTENTION TO
ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM.
• These instructions are aimed at professionally qualifi ed "INSTALLERS
OF ELECTRICAL EQUIPMENT" and must respect the local
standards and regulations in force. All materials used must be
approved and must suit the environment in which the installation
is situated.
• This appliance must be used exclusively for the purpose for which
it has been made. "i.e. for the automation of gates and doors"
Any non authorised modifi cations are to be considered improper
and therefore dangerous.
The manufacturer accepts no liability for situations arising from
the use of an electrical installation which does not conform to the
local standards and regulations in force and in particular when the
earthing circuit is not effi cient.
USE
The appliance may be used to operate hinged gates, with one or two
gate leaves. The appliances may be fi tted both to the right and to
the left of the passageway.
This manual covers the following models:
200/BL1924 Self locking electromechanical operator suitable for hinged
gates up to 2,0m in length and 150kg in weight (per gate leaf).
TECHNICAL DESCRIPTION
- 24V dc motor with a steel never ending screw.
- Carter in shock-proof plastic.
- Release mechanism components in shockproof plastic.
- Geared motor with steel gears enclosed in a die cast two-piece
aluminium shell.
- The geared motor is fi tted with two micro switches; one for closing
"FCC" and one for opening "FCA" (see wiring diagram).
- Motor support base in zinc-plated steel
- Articulated operator arm in die cast aluminium
- Lubrication using permanently fl uid grease.
ACCESSORIES
980/XLSE01-1 - Electric lock 12V ac-V83.
IMPORTANT! The geared motor is not fi tted with a torque
limiter. Only use an electronic programmer which has a torque limiter
with maximum force at the head of the gate equal to 150N (local
standards and regulations in force).

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the following
public safety conditions are satisfi ed:
1) Ensure that the gate operating installation is far enough away from
the main road to eliminate possible traffi c disruptions.
2) The operator must be installed on the inside of the property and not
on the public side of the gate. The gates must not swing outwards
onto a public area.
3) The gate operator is designed for use on gates through which
vehicles are passing. Pedestrians should use a separate entrance.
4) The gate must be in full view when it is operating therefore controls
must be situated in a position where the operator can see the
gate at all times.
5) At least two warning signs (similar to the example
on the right) should be placed, where they can
be easily seen by the public, in the area of
the system of automatic operation. One inside
the property and one on the public side of the
installation.
These signs must be indelible and not hidden by
any objects (such as tree branches, decorative
fencing etc.).
IMPORTANT REMARKS
6) Make sure that the end-user is aware that children and/or pets
must not be allowed to play within the area of a gate installation. If
possible include this in the warning signs.
7) Whenever a fully open gate leaf comes within 600mm of a fi xed
structure the space must be protected by an anticrush buffer
(fi g. 1, detail 11).
8) If you have any questions about the safety of the gate operating
system, do not install the operator. Contact your dealer for
assistance.
USER INSTRUCTIONS
WARNINGS FOR THE USER
Before carrying out any cleaning or maintenance operations make
sure the power is disconnected at the mains.
The minimum controls which may be installed are OPEN-STOP-
CLOSE, these controls must be installed in a location not accessible
to children.
During the opening/closing manoeuvre check for correct operation
and activate the emergency stop button in case of danger.
During blackouts the gate can be released and manually manoeuvred
using the supplied release key (see manual release pag.12).
Periodically check the moving parts for wear and tear and grease
if required, using lubricants which maintain their friction levels
unaltered throughout time and are suitable for temperatures of
-20 to +70°C.
In case of failure or operational anomalies switch off the power at the
mains do not attempt to repair the appliance yourself.
Periodically check the correct operation of all safety devices
(photoelectric cells etc.). Eventual repair work must be carried out by
specialised personnel using original spare parts.
The appliance is not suitable for continuous operation and must be
adjusted according to the model (see technical data on page 20).

INSTALLATION INSTRUCTIONS

Before starting with the installation of the system check that the
structure which is to be automated is in good working order and
respects the local standards and regulations in force.
To this end make sure that the gate is suffi ciently rigid (if necessary
reinforce the structure) and that the hinges turn easily.
You are advised to grease all the moving parts using lubricants which
maintain unaltered friction characteristics over a period of time and
are suitable for temperatures of -20 to +70°C.
• Check the safety measures between the fi xed and moving parts:
- a minimum space of 30 mm must always be left along the entire
distance between the gate and the support column measured
throughout the entire opening angle of the gate.
- make sure that the space between the bottom of the gate and
the pavement never exceeds 30 mm throughout the entire opening
angle of the gate.
• The surface of the gate must not feature openings which allow a
person's hand or foot to pass through.
• Check the exact positioning of the pivots and hinges, and their
good working order (the upper and lower hinges/pivots must be
aligned on the same axis).
ATTENZIONE
• Work out the run of the cables according to the command and
APERTURA AUTOMATICA
control devices fi tted and make sure the system conforms to the
NON AVVICINARSI
local standard and regulations in force (see installation example
fi g.1 pag. 2).
• Check that the appliance is suitable for the size, weight and
duty cycle of the gate to which it is to be applied (see duty cycle
on page 20)
NON PERMETTERE A BAMBINI O AD
ANIMALI DOMESTICI DI SOSTARE NEL
RAGGIO D'AZIONE DEL CANCELLO
11
IMPORTANT REMARKS
. NOT READING THESE IMPORTANT