HIKOKI UP 18DA Instrucciones De Manejo página 10

English
Lights ;
The battery remaining power is 25%–50%.
Lights ;
The battery remaining power is less than 25%.
Blinks ;
The battery remaining power is nearly empty.
Recharge the battery soonest possible.
Blinks ;
Output suspended due to high temperature.
Remove the battery from the tool and allow it to
fully cool down.
Blinks ;
Output suspended due to failure or malfunction.
The problem may be the battery so please
contact your dealer.
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains
the accessories listed on page 226.
Standard accessories are subject to change without notice.
APPLICATIONS
The tool is intended for inflating bicycle and car tyres and
sports equipment using the adapters supplied.
Furthermore, the tool is intended for inflating and deflating
recreational equipment such as air mattresses and beds.
○ The tool is of limited suitability for inflating large-volume
van tyres.
○ The tool is not suitable for operating air-powered tools.
○ The pressure gauge is not calibrated. Use a calibrated
pressure gauge. e.g. to check tyre pressures.
○ The use in the medical and food sector as well as
refilling of oxygen tanks is not permitted.
○ Explosive, flammable or harmful gases must not be
aspirated. Operation in potentially explosive rooms is
not permitted.
SPECIFICATIONS
1. Power tool
Model
Voltage
Power supply
Filling capacity
Max. pressure
Weight
*1 According to EPTA-Procedure 01/2014
Depending on attached battery.
The heaviest weight is measured with BSL36B18X
(sold separately).
UP18DA
18 V
Battery 18 V
In-Vehicle power supply
DC 12 V / 10 A
16 L/min @130 kPa
1100 kPa 160 psi 11 bar
3.8 kg (BSL36B18X)* 1
2.8 kg (without battery)
NOTE
Due to HiKOKI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.
2. Battery (sold separately)
Model
BSL36A18
BSL1850MA
*1 The tool itself will automatically switch over.
CHARGING
Before using the power tool, charge the battery as follows.
<UC18YSL3 (sold separately)>
1. Connect the charger's power cord to the
receptacle.
When connecting the plug of the charger to a
receptacle, the charge indicator lamp will blink in red.
(See Table 1)
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 4 (on page 3).
3. Charging
When inserting a battery in the charger, charging will
commence and the charge indicator lamp will blink in
blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
Table 1: Indications of the charge indicator lamp
ON/OFF at 0.5 sec. intervals
(RED)
Lights for 0.5 sec. at intervals of
1 sec. (BLUE)
Lights for 1 sec. at intervals of
0.5 sec. (BLUE)
Lights continuously (BLUE)
Lights continuously (Continuous
buzzer sound: about 6 sec.)
(GREEN)
ON/OFF at 0.3 sec. intervals
(RED)
ON/OFF at 0.1 sec. intervals
(Intermittent buzzer sound:
about 2 sec.) (PURPLE)
10
Voltage Battery capacity
36 / 18 V* 1 2.5 / 5.0 Ah*
18 V 5.0 Ah
Before charging *
Charged at less than
50%
Charged at less than
80%
Charged at more
than 80%
Charging complete
Overheat standby *
Charging impossible
* 3
1
1
2