HIKOKI N 1810DA Instrucciones De Manejo página 11

Charging time for
battery capacity, 6.0 Ah
approx. (At 20°C)
1.5 Ah
(× 2 unit)
Charging time for
multi volt battery 2.5 Ah
capacity, approx. (× 2 unit)
(At 20°C)
4.0 Ah
(× 2 unit)
Number of battery cells
Weight
NOTE
○ The recharging time may vary according to the ambient
temperature and power source voltage.
○ If charging takes a long time
– Charging will take longer at extremely low ambient
temperatures. Charge the battery in a warm location
(such as indoors).
– Do not block the air vent. Otherwise the interior will
overheat, reducing the charger's performance.
– If the cooling fan is not operating, contact a HiKOKI
Authorized Service Center for repairs.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
BEFORE USE
Action
Removing and inserting the battery
Charging
Remaining battery indicator
Selecting accessories
1. LED light warning signals (Fig. 4)
In case of operation error, LED light shows as below.
90 min
45 min
On 0.5 second/
Off 0.5 second
75 min
120 min
On 0.25 second/
Off 0.25 second
4–10
0.5 kg
On 0.05 second/
Off 0.05 second
2. Trigger Lock Mechanism (See Fig. 5)
WARNING
○ Make sure the trigger is locked when not firing staples.
○ This Stapler has a lock mechanism to prevent the
staples from being fired.
To lock the trigger:
Firmly press in the trigger lock button from the
To operate:
Firmly press in the trigger lock button from the
lock is released and the trigger can be pulled.
3. Checking push lever operations
WARNING
Make sure the trigger is locked when not firing staples.
(See Fig. 5)
Always make sure the trigger is locked and the battery
removed from the power tool when checking push lever
operations.
Check to make sure the push lever slides smoothly when
operated.
Clean the sliding area on the push lever if it doesn't slide
smoothly.
4. Testing the stapler
WARNING
○ Make sure the trigger is locked when not firing staples.
(See Fig. 5)
○ Never use Stapler unless push lever is operating
properly.
Before actually beginning the stapling work, test the Stapler
by using the checklist below. Conduct the tests in the
following order.
If abnormal operation occurs, stop using the Stapler and
contact a HiKOKI authorized service center immediately.
REMOVE ALL STAPLES AND BATTERY FROM
(1)
STAPLER.
–
–
Installing the battery. Do not operate the push lever or
(2)
trigger while installing the battery. (See Fig. 2)
Figure Page
Remove the finger from the trigger and press the push
(3)
lever against the workpiece.
2 2
3 2 –
13 4
— 259
11
Table 3
Empty-firing prevention function
was activated → Load staples.
Battery voltage drop → Replace
the battery.
Overloaded condition (staple
jam) → Remove the cause of the
overloading.
Temperature protection (stapler
body is hot) → Allow the stapler
body to cool sufficiently.
Possibly malfunctioning→
Request repairs from the dealer
where it was purchased.
ALL SCREWS MUST BE TIGHTENED.
THE PUSH LEVER AND TRIGGER MUST MOVE
SMOOTHLY.
THE STAPLER MUST NOT OPERATE.
English
side.
side. The