Publicidad
Idiomas disponibles
Idiomas disponibles
English
1.5 Ah
2.0 Ah
2.5 Ah
Charging time for
3.0 Ah
battery capacity,
approx. (At 20°C)
4.0 Ah
5.0 Ah
6.0 Ah
1.5 Ah
(× 2 unit)
Charging time for
multi volt battery
2.5 Ah
capacity, approx.
(× 2 unit)
(At 20°C)
4.0 Ah
(× 2 unit)
Number of battery cells
Charging voltage for USB
Charging current for USB
Weight
NOTE
○ The recharging time may vary according to the ambient
temperature and power source voltage.
○ If charging takes a long time
–
Charging will take longer at extremely low ambient
temperatures. Charge the battery in a warm location
(such as indoors).
–
Do not block the air vent. Otherwise the interior will
overheat, reducing the charger's performance.
–
If the cooling fan is not operating, contact a HiKOKI
Authorized Service Center for repairs.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
15 min
20 min
25 min
20 min
(BSL1430C,
BSL1830C: 30 min)
26 min
(BSL1840M: 40 min)
32 min
38 min
20 min
32 min
52 min
4–10
5 V
2 A
0.6 kg
16
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Mounting the shoulder belt
Installing the hose LED and replacing
the battery*
1
Switch operation
Adjusting the discharge pressure and
speed and discharge amounts*
How to use the LED light and the hose
LED*
3
Filling the grease with a cartridge*
Filling the grease from a bulk
container*
4
Filling the grease using a filler pump*
Filling the grease using a screw-in
cartridge*
4, *5
Air purge*
6
Grease discharging*
7
Mounting clamping coupler (sold
separately)
Remaining battery indicator
Charging a USB device from an
electrical outlet
Charging a USB device and battery
from an electrical outlet
How to recharge USB device
Selecting accessories
*1 Installing the hose LED and replacing the battery
Remove 2 button cells CR1620 and insert new batteries
CR1620 into the cover. Pay attention to the polarity!
*2 Adjusting the discharge pressure and speed (by means
of the shift knob) and discharge amounts (by means of
the dial)
NOTE
The shift knob can not be switched while the power tool
is turning. To switch the shift knob, stop the power tool,
then set the shift knob.
○ Select discharge pressure and speed by means of shift
knob
Low gear:
Working pressure 69 MPa,
discharge rate 115 ml/min
High gear:
Working pressure 41 MPa,
discharge rate 297 ml/min
Figure
Page
3
2
4
2
5
2
6
3
7
3
8
3
2
9
3
4
10
4
11
5
4
12
6
13
7
14
8
15
8
16
8
17
9
18-a
9
18-b
9
19
9
—
226
Publicidad
