Power Supply - Muse MT-101 LT Manual De Instrucciones

GB TURNTABLE STEREO SYSTEM
LOCATION AND DESCRIPTION CONTROLS
1. PLATTER
2. SPINDLE
3. 45 RPM ADAPTOR
4. LIFT LEVER
5. TONE ARM REST
6. SPEED SELECTOR(33/45/78)
7. STANDBY BUTTON
8. AUX IN JACK
9. TONE ARM
10. POWER ON/ OFF AND VOLUME CONTROL
11. POWER INDICATOR LIGHT
12. PHONES JACK
13. CARTRIDGE WITH STYLUS
14. LATCH

POWER SUPPLY

Using the AC adaptor
AC adaptor:
Input 100-240V 50/60Hz
Output 9V , 1000mA
HXT-3750 IB MUSE 001 REV0.indd 4
15. CARRYING HANDLE
16. SPEAKERS
17. DC IN 9V JACK
18. EXTERNAL DEVICE OUTPUT JACK
19. LED INDICATOR OF PLAY/PAUSE/RECORDING/
DELETE
20. USB PORT
21. PLAY/PAUSE BUTTON
22. RECORD BUTTON
23. BACK BUTTON
24. STOP BUTTON
25. DELETE BUTTON
26. NEXT BUTTON
27. FUNCTION SWITCH(PHONO/AUX-USB)
EN - 1
The supplied AC adaptor is suitable for use on AC main supplies of 100-240V
mains supply within these parameters.
IMPORTANT NOTICE
Automatic standby mode
In a concern of saving energy, when playback has reached to the end or listening volume is set at a very low level and no
control is operated on the device for a period of 2 hours, the unit will automatically switch to Standby mode(power indicator
turns Red).
To switch the unit ON again, press the STANDBY button, the POWER indicator turns Blue.
Caution:
* The included AC adapter is exclusively intended to be used with this device
* Turn off the power before unplugging the AC adapter to avoid damaging the device.
* In case of unused for long periods, unplug the AC adapter from the outlet.
* Place the unit near the outlet and make sure it is easily accessible. If a malfunction occurs, immediately disconnect the
unit from the wall outlet.
* The adapter enables you to unplug the unit. It must be easily accessible during use.
* To completely turn off power, unplug the adapter from the wall outlet.
* Never use a damaged power adapter. Place the power cord safely and so that you do not pinch or crush it. If the cable
is damaged, contact a repair service.
TURN ON/ OFF THE UNIT
1. To turn the unit on, rotate the ON/OFF switch clockwise until a "click" is heard and set the volume to a lower level.
2. When you have finished the unit, rotate the ON/OFF switch counter-clockwise until a "click" is heard to turn off the unit.
LISTEN TO THE PHONO
1. When the unit is on, set the PHONO/AUX-USB mode selector to PHONO/AUX position.
2. Remove the stylus cover from the stylus and have released the Tone arm rest.
3. Place a record on the turntable platter and select the desired speed (33/45/78) according to the record.
NOTE: If you are playing 45RPM singles, place the 45 RPM adapter on the center spindle (45RPM adaptor is located in
the holder near the tone arm).
4. Push up the lift lever to raise the tone arm and gently move the tone arm to the desired position onto the record, Push
down the lift lever, the tone arm slowly onto the record to start playing the record.
5. Adjust the volume control to your desired level.
6. The record will stop automatically when finish and you must return the tone arm to the arm rest manually.
IMPORTANT:
- Do not turn or stop the Turntable platter manually. Moving or jarring the Turntable platter without securing the Tone Arm
Clamp could result in damage to the Tone Arm or Stylus.
- The turntable function can not playback if the AUX in cable is connected to the unit.
USING THE AUX IN MODE
1. Connect one end of the cable to the auxiliary input connector of the unit(cable not supplied).
2. When the unit is on, set the PHONO/AUX-USB mode selector to PHONO/AUX position.
3. Normally use your external audio appliance, the sound automatically goes through the speakers of your device.
4. Adjust the volume to the desired level.
5. Disconnect the external appliance from the auxiliary input to stop playback.
LISTEN TO THE DEVICE USB
1. Connect a USB device containing MP3 files or MP3 player to the USB port.
2. When the unit is on, set the PHONO/AUX-USB mode selector to USB position. It will start to playback automatically,
LED indicator becomes Blue.
3. Adjust the volume to the desired level.
4. Press NEXT to skip forward to the next track or repeatedly to several tracks. Press BACK return to the beginning of the
track, or press repeatedly to skip backwards several tracks.
5. Press PLAY/PAUSE to pause the USB playback, LED indicator blinking.
6. Press STOP to stop the USB playback, LED indicator turns off.
7. During the USB playback, press and hold DELETE for 2 seconds to delete your current track, LED indicator will flashed
twice, once current track deleted that will play the next track automatically.
AC and should only be connected to a
EN - 2
2015/11/6 17:12:32